PDA

View Full Version : Are you good at reading machine drawings?



Mad Scientist
10-14-2008, 03:34 PM
Are you good at reading machine drawings? If so this puzzle should be a snap.

http://woodgears.ca/eyeball/

Also check out the woodworking section of the site, there’s some interesting stuff there.

Paul Alciatore
10-14-2008, 06:42 PM
N e a t . .

Lew Hartswick
10-14-2008, 06:55 PM
It dosen't seem to quit and give an answer as to how well you did .
...lew...

dan s
10-14-2008, 07:01 PM
it does after 3 times through each test, its doing an average.


It dosen't seem to quit and give an answer as to how well you did .
...lew...

smiller6912
10-14-2008, 07:05 PM
DUDE!....... That's a be-atch with a touch pad :p
I only got a 5.4

dockrat
10-14-2008, 07:11 PM
It dosen't seem to quit and give an answer as to how well you did .
...lew...

You have to go through it 3 times to get an average


Your inaccuracy by category:

Parallelogram 11.7 12.8 8.1
Midpoint 4.5 5.0 7.1
Bisect angle 0.0 4.0 12.6
Triangle center 5.2 5.6 5.0
Circle center 6.4 7.2 10.6
Right angle 0.6 3.8 2.0
Convergence 3.2 7.1 7.6


Average error: 6.20 (lower is better)

old eyes and sticky mouse LOL


Oppppps Dan beat me to it


.

clutch
10-14-2008, 07:35 PM
5.72 first time, 5.12 second time. 19 inch LCD monitor.

Clutch

Day later, more beerz

Your inaccuracy by category:

Parallelogram 6.1 3.2 3.0
Midpoint 4.0 2.2 4.5
Bisect angle 1.1 2.4 3.3
Triangle center 5.8 3.8 1.1
Circle center 3.6 5.4 3.6
Right angle 1.8 1.2 2.7
Convergence 4.1 2.2 8.1

Average error: 3.49 (lower is better)

Wish I had more beer.

Clutch

Ausserdog
10-14-2008, 08:40 PM
4.22 for me. Maybe could have done better - wife is calling me to dinner!

J Tiers
10-14-2008, 09:17 PM
optical mouse....

3.63, with one inexplicable 15.6 unit error...... I disputed that one, but it didn't care.

OldRedFord
10-14-2008, 09:26 PM
Your inaccuracy by category:

Parallelogram 26.9 14.0 13.0
Midpoint 4.2 11.7 1.0
Bisect angle 0.1 2.1 2.1
Triangle center 21.2 2.6 28.7
Circle center 1.4 2.0 5.4
Right angle 11.8 1.8 3.0
Convergence 0.0 3.6 5.0


Equidistant? :confused:

rantbot
10-14-2008, 09:28 PM
My word. Somebody sure went to a lot of trouble for, well, what, exactly?

Forrest Addy
10-14-2008, 10:01 PM
Stupid game!!

wierdscience
10-14-2008, 11:16 PM
A 3.85 then a 3.75 then a 2.9 not too bad.

This would be a good test to give some one looking to be a jobsite foreman.

datsun280zxt
10-15-2008, 09:46 PM
Parallelogram 2.2 4.0 13.3
Midpoint 2.8 3.6 7.1
Bisect angle 6.1 4.9 7.5
Triangle center 4.1 5.9 8.6
Circle center 6.1 3.2 5.8
Right angle 1.1 0.0 1.0
Convergence 7.3 1.4 4.1


Average error: 4.77 (lower is better)

I got bored by the 3rd round and started rushing it...lol. My patience today has been used up long before I got to the computer tonight.