Page 1 of 21 12311 ... LastLast
Threads 1 to 20 of 408

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 02:30 AM
    268 Pages
    1 2 3 ... 268
    • Replies: 2,673
    • Views: 8,757,973
    12-02-2016, 05:39 PM Go to last post
  2. Sticky Thread Sticky: Posting Photos

    Started by George Bulliss, 01-28-2014 03:17 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 22,341
    11-04-2016, 11:44 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 03:26 PM
    • Replies: 0
    • Views: 104,855
    04-21-2010, 03:26 PM Go to last post
    • Replies: 4
    • Views: 186
    Today, 05:14 AM Go to last post
  1. OT donor car for electric conversion

    Started by darryl, 12-05-2016 03:10 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 35
    • Views: 1,399
    Today, 05:07 AM Go to last post
  2. OT Where to find a new circuit card

    Started by ahidley, Today 03:46 AM
    • Replies: 3
    • Views: 30
    Today, 04:42 AM Go to last post
  3. Chinese 10x18 Lathe Spindle Noise - I think I know what's wrong?

    Started by mattthegamer463, Yesterday 12:22 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 30
    • Views: 660
    Today, 04:07 AM Go to last post
  4. OT? Tip: Marking Hole Locations Under a Counter Top

    Started by Paul Alciatore, Yesterday 03:03 AM
    2 Pages
    1 2
    • Replies: 15
    • Views: 504
    Today, 04:04 AM Go to last post
  5. Straight edge needed.

    Started by Mcostello, 12-06-2016 11:03 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 543
    Today, 03:44 AM Go to last post
  6. Machine painting advice DSG

    Started by blckbx, Yesterday 06:38 AM
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 545
    Today, 03:44 AM Go to last post
  7. Black Granite Surface PLates

    Started by JoeLee, 12-06-2016 10:36 PM
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 856
    Today, 03:41 AM Go to last post
  8. OT: computer overheating causing strange problems...?

    Started by DR, Yesterday 11:19 PM
    • Replies: 8
    • Views: 112
    Today, 01:41 AM Go to last post
  9. Heavier flywheels for the Kerzel hit and miss engine

    Started by brian Rupnow, 11-29-2016 11:26 AM
    9 Pages
    1 2 3 ... 9
    • Replies: 81
    • Views: 3,108
    Today, 01:39 AM Go to last post
    • Replies: 5
    • Views: 162
    Today, 12:25 AM Go to last post
  10. Clever old time oil delivery mechanisms?

    Started by Jmay, 12-01-2016 01:42 PM
    5 Pages
    1 2 3 ... 5
    • Replies: 40
    • Views: 2,580
    Today, 12:24 AM Go to last post
  11. OT: Replacing a beam supporting concrete block wall?

    Started by SirLesPatterson, 12-04-2016 05:10 PM
    3 Pages
    1 2 3
    • Replies: 26
    • Views: 1,275
    Yesterday, 11:55 PM Go to last post
  12. Spindle issues and questions

    Started by Black Forest, Yesterday 01:44 PM
    • Replies: 7
    • Views: 262
    Yesterday, 10:50 PM Go to last post
  13. Can I run 230/460 motors with 240/480 power

    Started by Tundra Twin Track, 12-06-2016 10:39 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 666
    Yesterday, 09:21 PM Go to last post
  14. Trav-a-Dials on a Chinese lathe

    Started by Dave C, 12-06-2016 04:37 PM
    • Replies: 8
    • Views: 525
    Yesterday, 09:13 PM Go to last post
  15. OT-Insulating Window Film

    Started by rws, 12-06-2016 03:11 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 707
    Yesterday, 06:23 PM Go to last post
  16. replacing quill and spindle bearings

    Started by rusty reamer, 12-06-2016 01:02 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 645
    Yesterday, 05:31 PM Go to last post
  17. Cutting ss tube.

    Started by plunger, 12-03-2016 04:33 AM
    2 Pages
    1 2
    • Replies: 13
    • Views: 621
    Yesterday, 05:13 PM Go to last post
  18. New DRO install

    Started by Seastar, 12-06-2016 05:34 PM
    • Replies: 9
    • Views: 419
    Yesterday, 05:05 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •