Page 1 of 21 12311 ... LastLast
Threads 1 to 20 of 415

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 02:30 AM
    348 Pages
    1 2 3 ... 348
    • Replies: 3,479
    • Views: 11,747,890
    01-19-2019, 09:36 PM Go to last post
  2. Sticky Thread Sticky: Posting Photos and Starting Threads

    Started by George Bulliss, 01-28-2014 03:17 PM
    3 Pages
    1 2 3
    adding photos, photos
    • Replies: 20
    • Views: 64,562
    07-20-2018, 07:07 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 03:26 PM
    • Replies: 0
    • Views: 117,787
    04-21-2010, 03:26 PM Go to last post
  1. Building your own Ball/Clutch

    Started by A.K. Boomer, Today 02:33 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 534
    Today, 11:33 PM Go to last post
  2. AMC Marlin

    Started by aostling, Today 12:41 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 32
    • Views: 1,008
    Today, 11:31 PM Go to last post
  3. Always good to see this show up in the mail

    Started by troyadamietz, Yesterday 12:56 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 715
    Today, 11:29 PM Go to last post
    • Replies: 8
    • Views: 373
    Today, 11:05 PM Go to last post
  4. What did you do today?

    Started by vpt, 03-13-2010 09:56 PM
    293 Pages
    1 2 3 ... 293
    • Replies: 2,925
    • Views: 511,391
    Today, 10:45 PM Go to last post
  5. OT Coil winding hints for very small wire?

    Started by J Tiers, Yesterday 05:41 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 467
    Today, 10:39 PM Go to last post
  6. Power supply for LED light

    Started by Black Forest, 01-31-2019 01:01 PM
    2 Pages
    1 2
    • Replies: 16
    • Views: 704
    Today, 10:29 PM Go to last post
  7. OT, Cable TV just went up $130/month..... Hulu?

    Started by DR, Today 01:16 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 329
    Today, 09:20 PM Go to last post
  8. OT: AMA Expo East

    Started by 3 Phase Lightbulb, Yesterday 11:59 PM
    • Replies: 5
    • Views: 193
    Today, 09:11 PM Go to last post
  9. OT Circuit Diagram Software (Free?)

    Started by olf20, 02-20-2019 02:29 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 583
    Today, 09:04 PM Go to last post
  10. Practical coefficient of friction question.

    Started by jmarkwolf, Yesterday 05:02 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 481
    Today, 06:24 PM Go to last post
  11. Lathe unloading

    Started by Commander_Chaos, 02-11-2019 06:51 PM
    • Replies: 8
    • Views: 364
    Today, 06:16 PM Go to last post
  12. Shop heater help needed

    Started by true temper, 02-19-2019 11:30 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 62
    • Views: 2,099
    Today, 05:32 PM Go to last post
  13. Design and build Side-shaft hit and miss from barstock

    Started by brian Rupnow, 11-14-2018 01:43 PM
    51 Pages
    1 2 3 ... 51
    • Replies: 505
    • Views: 31,504
    Today, 04:11 PM Go to last post
  14. Loctite 638 strength? Can I bodge it?!

    Started by Cenedd, Yesterday 07:02 PM
    • Replies: 4
    • Views: 279
    Today, 03:11 PM Go to last post
    • Replies: 6
    • Views: 239
    Today, 03:02 PM Go to last post
  15. Valentines day treasures

    Started by Dan Dubeau, 02-17-2019 10:52 AM
    6 Pages
    1 2 3 ... 6
    • Replies: 53
    • Views: 2,011
    Today, 02:16 PM Go to last post
  16. O.T. Drainage question

    Started by Mike Amick, 02-20-2019 08:56 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 35
    • Views: 1,046
    Today, 02:11 PM Go to last post
  17. Slitting Saw Arbor

    Started by enginuity, Yesterday 02:10 PM
    • Replies: 7
    • Views: 484
    Today, 01:31 PM Go to last post
  18. OT: Transformer Buzz

    Started by Joel, 02-16-2019 10:11 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 617
    Today, 09:12 AM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •