Page 1 of 18 12311 ... LastLast
Threads 1 to 20 of 358

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 01:30 AM
    303 Pages
    1 2 3 ... 303
    • Replies: 3,020
    • Views: 10,067,665
    08-16-2017, 02:59 PM Go to last post
  2. Sticky Thread Sticky: Posting Photos

    Started by George Bulliss, 01-28-2014 02:17 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 38,932
    07-23-2017, 08:57 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 02:26 PM
    • Replies: 0
    • Views: 109,952
    04-21-2010, 02:26 PM Go to last post
  1. Repairing Extension Cord Ground Pin

    Started by JoeLee, Yesterday 01:18 PM
    2 Pages
    1 2
    • Replies: 16
    • Views: 613
    Today, 12:54 PM Go to last post
  2. OT: Need advise on e-Bay local pickup

    Started by DS_park, 08-15-2017 08:59 AM
    2 Pages
    1 2
    • Replies: 15
    • Views: 727
    Today, 12:10 PM Go to last post
  3. Auto reverse mechanism

    Started by brian Rupnow, 08-05-2017 04:51 PM
    10 Pages
    1 2 3 ... 10
    • Replies: 97
    • Views: 6,813
    Today, 11:46 AM Go to last post
  4. Mars rover fastener, revisited

    Started by Dodd Stacy, 08-17-2017 09:59 AM
    5 Pages
    1 2 3 ... 5
    • Replies: 45
    • Views: 1,991
    Today, 11:41 AM Go to last post
  5. Mazda's Skyactiv-X engine

    Started by aostling, Yesterday 07:41 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 661
    Today, 11:37 AM Go to last post
  6. Carbide Router Bits in Mill

    Started by epicfail48, Yesterday 03:45 AM
    • Replies: 9
    • Views: 545
    Today, 10:24 AM Go to last post
  7. Incredible air hacksaw

    Started by Edwin Dirnbeck, 08-14-2017 08:53 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 1,148
    Today, 10:04 AM Go to last post
  8. Making a long flat bar on a vertical mill

    Started by mikey553, Yesterday 01:09 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 649
    Today, 08:42 AM Go to last post
  9. What is the benefit of air tools?

    Started by SirLesPatterson, 08-15-2017 06:27 AM
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 1,380
    Today, 07:13 AM Go to last post
  10. O/T: Vacuum Repair. My project of the day.

    Started by JRouche, Yesterday 12:05 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 619
    Today, 06:58 AM Go to last post
  11. The Napkin Ring Problem

    Started by H380, 08-16-2017 10:59 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 36
    • Views: 1,811
    Today, 02:52 AM Go to last post
  12. Spin indexer question

    Started by RichTes, 08-14-2017 12:42 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 879
    Today, 02:00 AM Go to last post
  13. Disrespectful younger generation

    Started by Forrest Addy, Yesterday 10:26 AM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 1,510
    Yesterday, 11:45 PM Go to last post
  14. Anyone heard of Triton Tools ?

    Started by Axkiker, Yesterday 10:53 AM
    • Replies: 7
    • Views: 437
    Yesterday, 11:19 PM Go to last post
  15. Two to three point contact tip from Steve Barton / Viperspit

    Started by pinstripe, 08-15-2017 06:40 PM
    3 Pages
    1 2 3
    • Replies: 29
    • Views: 1,453
    Yesterday, 10:39 PM Go to last post
  16. Way OT The Great Asparagus Patch wildfire in BC

    Started by jd99, 08-17-2017 01:37 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 940
    Yesterday, 06:46 PM Go to last post
  17. Turning rubber covered roller

    Started by BWS, Yesterday 09:03 AM
    2 Pages
    1 2
    • Replies: 19
    • Views: 611
    Yesterday, 06:43 PM Go to last post
  18. Norman's Jib Crane adventure

    Started by Norman Bain, 04-16-2017 08:00 PM
    15 Pages
    1 2 3 ... 15
    • Replies: 147
    • Views: 17,375
    Yesterday, 05:28 PM Go to last post
  19. Lapping 2.5” diameter aluminum bore

    Started by mikey553, 03-30-2017 07:36 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 37
    • Views: 3,547
    Yesterday, 03:54 PM Go to last post
  20. Cable strain relief retrofit

    Started by RichR, Yesterday 01:16 AM
    • Replies: 9
    • Views: 429
    Yesterday, 01:39 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •