Page 1 of 17 12311 ... LastLast
Threads 1 to 20 of 325

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Posting Photos and Starting Threads

    Started by George Bulliss, 01-28-2014 02:17 PM
    3 Pages
    1 2 3
    adding photos, photos
    • Replies: 25
    • Views: 54,439
    06-15-2018, 10:44 PM Go to last post
  2. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 01:30 AM
    334 Pages
    1 2 3 ... 334
    • Replies: 3,336
    • Views: 11,100,584
    06-13-2018, 10:14 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 02:26 PM
    • Replies: 0
    • Views: 115,025
    04-21-2010, 02:26 PM Go to last post
  1. What is your favorite material to machine.

    Started by 754, Today 03:32 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 303
    Today, 10:09 PM Go to last post
  2. Installing a cheap DRO?

    Started by Doc Nickel, 05-31-2018 04:48 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 868
    Today, 10:09 PM Go to last post
  3. OT: A strange and delightful backyard encounter

    Started by Horst, Today 03:15 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 411
    Today, 10:02 PM Go to last post
  4. OT: Holding Pattern (kidney stones)

    Started by 3 Phase Lightbulb, 06-14-2018 05:52 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 1,003
    Today, 09:58 PM Go to last post
  5. DC motor controler

    Started by radkins, 06-15-2018 03:27 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 39
    • Views: 1,142
    Today, 09:13 PM Go to last post
  6. What did you do today?

    Started by vpt, 03-13-2010 08:56 PM
    98 Pages
    1 2 3 ... 98
    • Replies: 977
    • Views: 298,000
    Today, 09:10 PM Go to last post
  7. Surface grinder motor?

    Started by engineerd3d, Today 10:13 AM
    • Replies: 4
    • Views: 206
    Today, 08:28 PM Go to last post
  8. O/T: Dropped the Load.

    Started by JRouche, Yesterday 12:45 AM
    2 Pages
    1 2
    • Replies: 17
    • Views: 1,078
    Today, 06:03 PM Go to last post
  9. ok, so I created a photo album

    Started by Horst, Today 03:38 PM
    • Replies: 3
    • Views: 149
    Today, 06:00 PM Go to last post
  10. In over my head on 1st lathe

    Started by Mr-Mike, 04-26-2018 06:32 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 66
    • Views: 5,368
    Today, 05:36 PM Go to last post
  11. stiffest grade of aluminum for machine-only (no post treatment)

    Started by MCARSON, 06-15-2018 07:52 PM
    3 Pages
    1 2 3
    aluminum grades
    • Replies: 28
    • Views: 1,326
    Today, 03:45 PM Go to last post
    • Replies: 9
    • Views: 548
    Today, 02:49 PM Go to last post
  12. Gearing up my Smithy 1220LTD mini 3-in-1 machine

    Started by General Zod, 06-10-2018 12:34 PM
    3 Pages
    1 2 3
    • Replies: 24
    • Views: 785
    Today, 02:42 PM Go to last post
  13. Thoughts On Threading These Shanks......

    Started by JoeLee, 06-13-2018 03:26 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 30
    • Views: 1,291
    Today, 02:06 PM Go to last post
  14. 21" Royersford Excelsior Restoration

    Started by The Metal Butcher, 06-14-2018 12:37 PM
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 1,101
    Today, 12:57 PM Go to last post
  15. Double acting Double cylinder Oscillator

    Started by brian Rupnow, 05-23-2018 08:51 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 104
    • Views: 5,706
    Today, 11:40 AM Go to last post
  16. Bench grinder tool rests, tilt or not?

    Started by DennisCA, 06-08-2018 01:43 AM
    9 Pages
    1 2 3 ... 9
    • Replies: 80
    • Views: 4,669
    Today, 05:06 AM Go to last post
    • Replies: 9
    • Views: 509
    Today, 02:00 AM Go to last post
  17. Multi sheave pulley and vfd

    Started by challenger, 06-14-2018 09:31 AM
    2 Pages
    1 2
    • Replies: 13
    • Views: 558
    Yesterday, 09:53 PM Go to last post
  18. rpm for tapping heads

    Started by 1-800miner, 06-12-2018 11:35 AM
    2 Pages
    1 2
    • Replies: 19
    • Views: 763
    Yesterday, 08:55 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •