Page 1 of 16 12311 ... LastLast
Threads 1 to 20 of 303

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 01:30 AM
    359 Pages
    1 2 3 ... 359
    • Replies: 3,584
    • Views: 12,448,989
    Today, 03:42 PM Go to last post
  2. Sticky Thread Sticky: Posting Photos and Starting Threads

    Started by George Bulliss, 01-28-2014 02:17 PM
    3 Pages
    1 2 3
    adding photos, photos
    • Replies: 21
    • Views: 73,640
    08-30-2019, 05:02 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 02:26 PM
    • Replies: 0
    • Views: 120,092
    04-21-2010, 02:26 PM Go to last post
  1. Removing bearings from a shaft - without damaging them??

    Started by Mcgyver, 10-13-2019 10:55 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 31
    • Views: 926
    Today, 04:04 PM Go to last post
  2. Music wire vs W2

    Started by hitnmiss, Yesterday 09:49 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 341
    Today, 04:00 PM Go to last post
  3. Old School Sawmill Edger

    Started by brian Rupnow, 10-13-2019 11:43 AM
    3 Pages
    1 2 3
    • Replies: 28
    • Views: 930
    Today, 03:33 PM Go to last post
    • Replies: 6
    • Views: 554
    Today, 03:31 PM Go to last post
  4. Insane Toolbox Advertisement from Shopify/Facebook

    Started by Bob La Londe, Today 01:26 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 186
    Today, 03:27 PM Go to last post
  5. Making a gear

    Started by small.planes, 10-02-2019 07:54 AM
    5 Pages
    1 2 3 ... 5
    • Replies: 40
    • Views: 1,966
    Today, 03:18 PM Go to last post
  6. OT: New Ranger pickup impressions so far

    Started by J Tiers, 10-06-2019 07:51 PM
    12 Pages
    1 2 3 ... 12
    • Replies: 113
    • Views: 4,221
    Today, 02:37 PM Go to last post
  7. O/T: Cranes falling over. New construction falling over.

    Started by JRouche, 10-12-2019 10:31 PM
    3 Pages
    1 2 3
    • Replies: 28
    • Views: 1,806
    Today, 02:22 PM Go to last post
  8. OT - New leaf vac solution for tractor

    Started by Glug, 10-13-2019 11:37 AM
    2 Pages
    1 2
    diy, leaf, tractor, vacuum
    • Replies: 14
    • Views: 560
    Today, 02:10 PM Go to last post
  9. OT- one-button hide desktop

    Started by darryl, Yesterday 03:47 AM
    2 Pages
    1 2
    • Replies: 13
    • Views: 533
    Today, 01:35 PM Go to last post
    • Replies: 14
    • Views: 445
    Today, 01:34 PM Go to last post
  10. Fabricating an impossible to find oil tank for a motorcycle

    Started by jhe.1973, 09-13-2011 01:45 PM
    15 Pages
    1 2 3 ... 15
    • Replies: 145
    • Views: 51,386
    Today, 01:30 PM Go to last post
  11. Another what is it

    Started by true temper, 10-13-2019 08:46 PM
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 1,225
    Today, 12:34 PM Go to last post
  12. Cool OT: Adventures in troubleshooting and repair - mini SW radio

    Started by PStechPaul, 10-21-2016 09:16 PM
    2 Pages
    1 2
    batteries, leakage, printed circuit board, radio, repair
    • Replies: 11
    • Views: 1,883
    Today, 12:03 PM Go to last post
  13. OT: what is the most unusual pet ever.

    Started by loose nut, 10-13-2019 10:38 AM
    5 Pages
    1 2 3 ... 5
    • Replies: 45
    • Views: 1,630
    Today, 11:09 AM Go to last post
  14. Best way to remove burrs from a hole

    Started by DennisCA, Today 06:03 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 249
    Today, 10:10 AM Go to last post
  15. radial arm saw repair.

    Started by plunger, 10-13-2019 04:00 AM
    3 Pages
    1 2 3
    • Replies: 29
    • Views: 977
    Today, 09:36 AM Go to last post
  16. Is AL51G any good

    Started by Kiwipaulnz, Today 12:39 AM
    • Replies: 3
    • Views: 172
    Today, 05:45 AM Go to last post
  17. Farm machine shop set up after a long absence

    Started by Hawkin45, 10-10-2019 10:30 PM
    2 Pages
    1 2
    d1-4, de valliere, farm, south bend
    • Replies: 12
    • Views: 1,136
    Today, 12:01 AM Go to last post
  18. Restoring plating

    Started by alanganes, 10-13-2019 08:44 PM
    • Replies: 9
    • Views: 399
    Yesterday, 05:54 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •