Page 1 of 18 12311 ... LastLast
Threads 1 to 20 of 349

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 01:30 AM
    306 Pages
    1 2 3 ... 306
    • Replies: 3,054
    • Views: 10,236,525
    09-20-2017, 07:21 PM Go to last post
  2. Sticky Thread Sticky: Posting Photos

    Started by George Bulliss, 01-28-2014 02:17 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 40,976
    07-23-2017, 08:57 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 02:26 PM
    • Replies: 0
    • Views: 110,632
    04-21-2010, 02:26 PM Go to last post
  1. CNC, Stepper Motors, and Cheap Mill Drill (HF) retrofit

    Started by 01-7700, Yesterday 06:46 AM
    2 Pages
    1 2
    • Replies: 17
    • Views: 596
    Today, 05:44 PM Go to last post
  2. Broken taps. Please exsplain . . .

    Started by Planeman41, Today 12:33 PM
    2 Pages
    1 2
    tapping, taps
    • Replies: 15
    • Views: 341
    Today, 05:39 PM Go to last post
  3. Overhead lights for lathe...

    Started by 3 Phase Lightbulb, Today 03:32 PM
    • Replies: 6
    • Views: 73
    Today, 05:32 PM Go to last post
  4. Logan Lathe Question

    Started by CPeter, Today 10:39 AM
    • Replies: 4
    • Views: 118
    Today, 05:30 PM Go to last post
  5. Concrete dust

    Started by SirLesPatterson, Yesterday 06:41 AM
    6 Pages
    1 2 3 ... 6
    • Replies: 50
    • Views: 1,190
    Today, 05:28 PM Go to last post
  6. heat sinks and materials choice

    Started by darryl, Yesterday 03:30 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 471
    Today, 05:25 PM Go to last post
  7. Disaster in Dayton... End of an Era... Je suis désolé

    Started by Dan_the_Chemist, 09-23-2017 08:57 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 1,595
    Today, 04:41 PM Go to last post
  8. Centroid finally accepting Acorn orders.

    Started by DICKEYBIRD, 08-02-2017 10:39 AM
    8 Pages
    1 2 3 ... 8
    • Replies: 71
    • Views: 6,719
    Today, 04:17 PM Go to last post
  9. Syncrowave 250 welder question

    Started by Mr Fixit, 04-08-2017 08:38 PM
    • Replies: 6
    • Views: 741
    Today, 04:04 PM Go to last post
  10. OT:Floor beam span calculation for SPFs

    Started by 3 Phase Lightbulb, Yesterday 03:47 PM
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 584
    Today, 03:42 PM Go to last post
    • Replies: 0
    • Views: 37
    Today, 03:38 PM Go to last post
  11. Rusty chuck

    Started by elf, 09-17-2017 02:55 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 34
    • Views: 1,419
    Today, 03:13 PM Go to last post
  12. Welding near bearings

    Started by Grimm, 09-20-2017 10:35 AM
    2 Pages
    1 2
    bearing, motorcycle, welding
    • Replies: 16
    • Views: 701
    Today, 03:06 PM Go to last post
  13. OT: SSD versus hard drive.

    Started by goose, 09-22-2017 05:19 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 36
    • Views: 1,599
    Today, 02:39 PM Go to last post
  14. OT- Equifax

    Started by Abner, 09-23-2017 09:09 AM
    6 Pages
    1 2 3 ... 6
    • Replies: 51
    • Views: 1,542
    Today, 02:37 PM Go to last post
  15. I am effed up

    Started by Weston Bye, 09-17-2017 02:07 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 66
    • Views: 4,474
    Today, 02:20 PM Go to last post
  16. New BP Mill - Disapointment Number One.

    Started by CCWKen, 09-22-2017 09:23 AM
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 1,653
    Today, 02:00 PM Go to last post
  17. OT Do you think a carbide blade would handle this ?

    Started by Mike Amick, Yesterday 12:14 AM
    3 Pages
    1 2 3
    • Replies: 24
    • Views: 884
    Today, 01:27 PM Go to last post
  18. Barley mill plans or ideas.

    Started by Jon Heron, Yesterday 04:09 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 483
    Today, 12:42 PM Go to last post
  19. Looking to drill a small hole- 94 gauge (.007 in, .180mm)….

    Started by DS_park, 09-24-2017 09:58 AM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 821
    Today, 12:27 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •