Page 1 of 15 12311 ... LastLast
Threads 1 to 20 of 296

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 01:30 AM
    357 Pages
    1 2 3 ... 357
    • Replies: 3,561
    • Views: 12,114,482
    07-31-2019, 11:52 PM Go to last post
  2. Sticky Thread Sticky: Posting Photos and Starting Threads

    Started by George Bulliss, 01-28-2014 02:17 PM
    3 Pages
    1 2 3
    adding photos, photos
    • Replies: 20
    • Views: 70,033
    07-20-2018, 06:07 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 02:26 PM
    • Replies: 0
    • Views: 119,444
    04-21-2010, 02:26 PM Go to last post
  1. 3 Phase motor noise?

    Started by Mopar_Mudder, 08-11-2019 01:47 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 32
    • Views: 905
    Today, 08:30 PM Go to last post
  2. OT: Low voltage digital circuit and shielded cable

    Started by QSIMDO, Today 05:42 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 94
    Today, 08:11 PM Go to last post
    • Replies: 20
    • Views: 561
    Today, 07:55 PM Go to last post
  3. I am bored out of my mind... Ideas...

    Started by RB211, Today 04:06 AM
    2 Pages
    1 2
    • Replies: 14
    • Views: 619
    Today, 06:11 PM Go to last post
  4. Vertical hit and miss engine

    Started by brian Rupnow, 06-15-2019 11:17 AM
    21 Pages
    1 2 3 ... 21
    • Replies: 201
    • Views: 16,903
    Today, 05:54 PM Go to last post
  5. Holex Corp. Trepanning Tool

    Started by JoeLee, Today 01:26 PM
    • Replies: 1
    • Views: 132
    Today, 05:19 PM Go to last post
  6. Your experience with 6 inch Chinese rotary tables.

    Started by Rustybolt, 08-16-2019 08:34 AM
    2 Pages
    1 2
    • Replies: 15
    • Views: 833
    Today, 05:16 PM Go to last post
  7. Carbide end mills, short life

    Started by quadrod, Today 12:19 AM
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 554
    Today, 04:56 PM Go to last post
  8. Chuck backing plate question.

    Started by Mr Fixit, 07-19-2017 01:42 AM
    3 Pages
    1 2 3
    • Replies: 26
    • Views: 3,464
    Today, 04:54 PM Go to last post
  9. Does anyone have a Hardinge Copycat Lathe?

    Started by hammernanvil, Yesterday 03:33 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 345
    Today, 03:50 PM Go to last post
    • Replies: 5
    • Views: 159
    Today, 01:35 PM Go to last post
  10. Off topic car battery corosion nonsence

    Started by Edwin Dirnbeck, Yesterday 08:29 AM
    2 Pages
    1 2
    • Replies: 14
    • Views: 680
    Today, 12:44 PM Go to last post
  11. Boxford vsl 500 what is this screw for? How do i remove chuck?

    Started by apples, 08-16-2019 04:07 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 34
    • Views: 1,095
    Today, 12:25 PM Go to last post
  12. New Bandsaw (NEW new)

    Started by Bob La Londe, 08-14-2019 06:42 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 971
    Today, 12:22 PM Go to last post
  13. What did you machine today?

    Started by vpt, 04-20-2013 03:53 PM
    155 Pages
    1 2 3 ... 155
    • Replies: 1,542
    • Views: 518,731
    Today, 11:50 AM Go to last post
  14. black stain under chuck - yuck

    Started by metalmagpie, Today 05:29 AM
    • Replies: 4
    • Views: 305
    Today, 11:08 AM Go to last post
  15. What did you do today?

    Started by vpt, 03-13-2010 08:56 PM
    441 Pages
    1 2 3 ... 441
    • Replies: 4,406
    • Views: 741,987
    Today, 10:59 AM Go to last post
  16. More boring tooling...

    Started by Dan Dubeau, 08-09-2019 08:53 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 1,126
    Today, 10:26 AM Go to last post
  17. Info ref CO2 extinguishers.

    Started by Dunc, 08-16-2019 12:27 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 561
    Today, 10:25 AM Go to last post
  18. My old yahoo group. Bridgeport Mill Group-closing

    Started by JRouche, 04-05-2019 02:05 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 1,200
    Today, 09:57 AM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •