Page 1 of 16 12311 ... LastLast
Threads 1 to 20 of 316

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 01:30 AM
    307 Pages
    1 2 3 ... 307
    • Replies: 3,063
    • Views: 10,306,599
    Today, 05:04 PM Go to last post
  2. Sticky Thread Sticky: Help for an Apprentice

    Started by George Bulliss, Today 10:14 AM
    • Replies: 3
    • Views: 214
    Today, 01:15 PM Go to last post
  3. Sticky Thread Sticky: Posting Photos

    Started by George Bulliss, 01-28-2014 02:17 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 41,958
    07-23-2017, 08:57 PM Go to last post
  4. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 02:26 PM
    • Replies: 0
    • Views: 110,953
    04-21-2010, 02:26 PM Go to last post
  1. 3hp, New GE 3ph motors $49 @Surplus Center

    Started by flylo, Today 07:52 AM
    3 Pages
    1 2 3
    • Replies: 24
    • Views: 584
    Today, 09:13 PM Go to last post
  2. Help self holding tire inflating Chuck

    Started by Edwin Dirnbeck, Today 10:09 AM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 438
    Today, 09:12 PM Go to last post
  3. A Tiny 3 cylinder Holt based engine

    Started by gbritnell, Today 04:52 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 206
    Today, 09:01 PM Go to last post
  4. Bolt Grades...for sure?

    Started by Dunc, Today 10:40 AM
    • Replies: 7
    • Views: 291
    Today, 08:58 PM Go to last post
    • Replies: 1
    • Views: 26
    Today, 08:53 PM Go to last post
  5. OT. Car restoration forum suggestions

    Started by Mr Fixit, 10-16-2017 09:31 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 922
    Today, 08:48 PM Go to last post
  6. Harbor Freight Mill Drill Moving

    Started by 01-7700, 10-17-2017 01:31 PM
    6 Pages
    1 2 3 ... 6
    • Replies: 51
    • Views: 1,473
    Today, 08:42 PM Go to last post
  7. A powered Z-axis for my bench top mill

    Started by jariou, 10-17-2017 10:32 PM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 644
    Today, 08:41 PM Go to last post
    • Replies: 2
    • Views: 57
    Today, 08:36 PM Go to last post
  8. Back to Steam--

    Started by brian Rupnow, 09-04-2017 04:09 PM
    21 Pages
    1 2 3 ... 21
    • Replies: 203
    • Views: 14,585
    Today, 08:30 PM Go to last post
  9. Boring hole tapered

    Started by Lew Hartswick, Yesterday 11:15 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 432
    Today, 07:51 PM Go to last post
  10. ER Collets and Drill Bits

    Started by mattthegamer463, Today 10:11 AM
    2 Pages
    1 2
    • Replies: 14
    • Views: 347
    Today, 07:48 PM Go to last post
  11. HF 2 Ton Shop Crane

    Started by 3 Phase Lightbulb, 10-17-2017 04:10 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 62
    • Views: 2,433
    Today, 07:28 PM Go to last post
  12. Fancy motorcycle plate holder

    Started by jariou, 10-09-2017 05:02 PM
    5 Pages
    1 2 3 ... 5
    • Replies: 47
    • Views: 2,500
    Today, 07:16 PM Go to last post
  13. APKT 1003 vs 11T308

    Started by Tony, 03-13-2016 03:38 PM
    • Replies: 6
    • Views: 1,243
    Today, 07:00 PM Go to last post
  14. OT: WPA2 broken

    Started by ironmonger, 10-17-2017 05:12 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 32
    • Views: 1,195
    Today, 06:02 PM Go to last post
  15. deburing holes

    Started by darryl, Yesterday 03:55 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 556
    Today, 05:47 PM Go to last post
  16. OT- Bandwidth Usage

    Started by rws, 10-17-2017 12:48 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 561
    Today, 05:07 PM Go to last post
  17. On the hunt for all 10 HSM's with Mike Wards scraping articles

    Started by doctordoctor, 01-30-2015 07:44 PM
    3 Pages
    1 2 3
    • Replies: 27
    • Views: 6,155
    Today, 05:05 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •