Page 1 of 23 12311 ... LastLast
Threads 1 to 20 of 456

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 01:30 AM
    287 Pages
    1 2 3 ... 287
    • Replies: 2,867
    • Views: 9,405,713
    Today, 01:06 PM Go to last post
  2. Sticky Thread Sticky: Posting Photos

    Started by George Bulliss, 01-28-2014 02:17 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 29,061
    Yesterday, 01:02 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 02:26 PM
    • Replies: 0
    • Views: 107,149
    04-21-2010, 02:26 PM Go to last post
  1. back from Baja

    Started by metalmagpie, Yesterday 05:48 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 445
    Today, 01:19 PM Go to last post
  2. Smile I brought home a new mill

    Started by Cuttings, Yesterday 11:21 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 320
    Today, 01:04 PM Go to last post
  3. OT - How would you clean these grills/grates?

    Started by challenger, 03-23-2017 01:57 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 32
    • Views: 1,426
    Today, 12:24 PM Go to last post
  4. Newbie Question: Lathe Leadscrew Handwheel

    Started by benjaminh, Yesterday 04:43 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 473
    Today, 11:58 AM Go to last post
  5. Belt grinder plans?

    Started by QSIMDO, 03-23-2017 05:34 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 35
    • Views: 1,321
    Today, 11:54 AM Go to last post
  6. Introduction - New Member

    Started by ConductorX, Today 08:52 AM
    • Replies: 3
    • Views: 90
    Today, 11:53 AM Go to last post
  7. Fractional Hp motor ratings

    Started by Dunc, 03-23-2017 09:02 PM
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 580
    Today, 11:45 AM Go to last post
  8. Free Lathe

    Started by George Bulliss, 03-23-2017 09:20 AM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 1,917
    Today, 11:04 AM Go to last post
  9. How to test Treadmill Motor

    Started by Tundra Twin Track, 03-22-2017 09:58 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 39
    • Views: 1,504
    Today, 10:39 AM Go to last post
  10. Downsizing from large machines.

    Started by Vee3, 03-23-2017 02:11 AM
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 1,326
    Today, 10:34 AM Go to last post
  11. Linuxcnc Q and A

    Started by skunkworks, Yesterday 10:35 AM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 658
    Today, 10:14 AM Go to last post
  12. Lubricating rollers for saw infeed/outfeed

    Started by winchman, 03-23-2017 01:42 AM
    2 Pages
    1 2
    • Replies: 19
    • Views: 774
    Today, 10:08 AM Go to last post
  13. evidence of a nice tram

    Started by A.K. Boomer, 03-21-2017 12:37 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 2,025
    Today, 09:52 AM Go to last post
  14. What can I do with a motorized wheelchair?

    Started by Dave C, 03-23-2017 12:33 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 867
    Today, 08:59 AM Go to last post
  15. "Weak link"

    Started by Jim Hubbell, 09-24-2016 10:06 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 39
    • Views: 3,351
    Today, 08:38 AM Go to last post
  16. What did you machine today?

    Started by vpt, 04-20-2013 03:53 PM
    46 Pages
    1 2 3 ... 46
    • Replies: 455
    • Views: 166,178
    Today, 07:10 AM Go to last post
  17. DSG 13/30 oil leak

    Started by blckbx, Yesterday 04:02 PM
    • Replies: 2
    • Views: 135
    Today, 04:58 AM Go to last post
  18. Compressor motor - high current draw

    Started by aribert, 03-13-2017 12:58 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 890
    Today, 01:16 AM Go to last post
    • Replies: 12
    • Views: 561
    Today, 01:14 AM Go to last post
  19. Mounting a right angle attachment using shims

    Started by asallwey, 03-23-2017 09:40 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 535
    Yesterday, 09:21 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •