Page 1 of 21 12311 ... LastLast
Threads 1 to 20 of 411

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 02:30 AM
    348 Pages
    1 2 3 ... 348
    • Replies: 3,479
    • Views: 11,674,787
    01-19-2019, 09:36 PM Go to last post
  2. Sticky Thread Sticky: Posting Photos and Starting Threads

    Started by George Bulliss, 01-28-2014 03:17 PM
    3 Pages
    1 2 3
    adding photos, photos
    • Replies: 20
    • Views: 63,487
    07-20-2018, 07:07 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 03:26 PM
    • Replies: 0
    • Views: 117,438
    04-21-2010, 03:26 PM Go to last post
  1. Level your lathe!

    Started by skunkworks, 01-20-2019 05:08 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 762
    Today, 01:12 AM Go to last post
  2. Is this still a machinist forum?

    Started by Boats69, 01-18-2019 11:24 AM
    13 Pages
    1 2 3 ... 13
    • Replies: 125
    • Views: 5,342
    Today, 12:47 AM Go to last post
  3. radios in a shop

    Started by Hubbard, Yesterday 09:47 AM
    5 Pages
    1 2 3 ... 5
    • Replies: 47
    • Views: 1,238
    Yesterday, 11:36 PM Go to last post
  4. Early Atlas shaper database

    Started by ncjeeper, 01-18-2019 05:54 PM
    3 Pages
    1 2 3
    • Replies: 26
    • Views: 759
    Yesterday, 11:25 PM Go to last post
  5. Bernay Engine machining content

    Started by sid pileski, Yesterday 08:38 PM
    • Replies: 8
    • Views: 139
    Yesterday, 11:03 PM Go to last post
  6. Differing amp readings from 2 meters!

    Started by gellfex, 01-19-2019 07:38 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 31
    • Views: 964
    Yesterday, 10:52 PM Go to last post
  7. cable sheath

    Started by darryl, Yesterday 07:25 PM
    • Replies: 4
    • Views: 144
    Yesterday, 10:28 PM Go to last post
  8. Design and build Side-shaft hit and miss from barstock

    Started by brian Rupnow, 11-14-2018 01:43 PM
    35 Pages
    1 2 3 ... 35
    • Replies: 342
    • Views: 19,774
    Yesterday, 10:14 PM Go to last post
  9. DIY 2x72 belt grinder build.

    Started by vpt, 01-18-2019 08:29 AM
    6 Pages
    1 2 3 ... 6
    • Replies: 56
    • Views: 1,787
    Yesterday, 09:54 PM Go to last post
  10. DRO scales Magnetic vs glass

    Started by rolland, Yesterday 05:56 PM
    • Replies: 2
    • Views: 93
    Yesterday, 09:21 PM Go to last post
  11. Slip roll question.

    Started by 754, 01-20-2019 03:52 PM
    • Replies: 9
    • Views: 235
    Yesterday, 08:54 PM Go to last post
  12. Question Cyanoacrylate adhesive (gel) and activator -- best buy?

    Started by fixerdave, 01-20-2019 05:55 AM
    3 Pages
    1 2 3
    • Replies: 26
    • Views: 817
    Yesterday, 08:40 PM Go to last post
  13. A “what is it “ question

    Started by plastikosmd, 01-20-2019 03:50 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 621
    Yesterday, 08:00 PM Go to last post
  14. Can anyone advise what these are?

    Started by Joe From NY, 01-19-2019 06:14 PM
    6 Pages
    1 2 3 ... 6
    • Replies: 54
    • Views: 3,602
    Yesterday, 07:47 PM Go to last post
  15. Twin insert tool on ebay

    Started by old mart, Yesterday 04:58 PM
    • Replies: 2
    • Views: 174
    Yesterday, 07:07 PM Go to last post
  16. Abom79 Out on his own.

    Started by hammernanvil, 01-18-2019 10:07 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 67
    • Views: 4,883
    Yesterday, 06:17 PM Go to last post
  17. Slap it on a grinder - Sacrilege!!!

    Started by Bob La Londe, 01-20-2019 07:54 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 788
    Yesterday, 06:05 PM Go to last post
  18. Question about non sparking tools.

    Started by 1-800miner, Yesterday 04:32 PM
    • Replies: 2
    • Views: 130
    Yesterday, 04:53 PM Go to last post
  19. Corded .25" straight die grinder recommendations

    Started by QSIMDO, 01-10-2019 01:07 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 34
    • Views: 1,558
    Yesterday, 02:02 PM Go to last post
  20. Great forum! OT slightly

    Started by im#2, 01-20-2019 03:27 PM
    • Replies: 7
    • Views: 383
    Yesterday, 01:01 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •