Page 1 of 18 12311 ... LastLast
Threads 1 to 20 of 360

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 01:30 AM
    349 Pages
    1 2 3 ... 349
    • Replies: 3,487
    • Views: 11,823,179
    03-20-2019, 03:20 PM Go to last post
  2. Sticky Thread Sticky: Posting Photos and Starting Threads

    Started by George Bulliss, 01-28-2014 02:17 PM
    3 Pages
    1 2 3
    adding photos, photos
    • Replies: 20
    • Views: 65,762
    07-20-2018, 06:07 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 02:26 PM
    • Replies: 0
    • Views: 118,138
    04-21-2010, 02:26 PM Go to last post
    • Replies: 9
    • Views: 268
    Today, 07:05 PM Go to last post
  1. OT Maybe - Phillips Driver Tip Geometry

    Started by rjs44032, Today 02:05 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 340
    Today, 06:53 PM Go to last post
  2. I need to get a metric tatooo

    Started by Edwin Dirnbeck, 03-17-2019 11:11 AM
    14 Pages
    1 2 3 ... 14
    • Replies: 135
    • Views: 4,645
    Today, 06:11 PM Go to last post
  3. What did you do today?

    Started by vpt, 03-13-2010 08:56 PM
    325 Pages
    1 2 3 ... 325
    • Replies: 3,241
    • Views: 551,858
    Today, 05:49 PM Go to last post
  4. Sideshaft i.c. Horizontal Engine

    Started by brian Rupnow, 03-19-2019 03:48 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 34
    • Views: 1,492
    Today, 05:41 PM Go to last post
  5. OT mower PTO switch question

    Started by strokersix, Yesterday 11:28 AM
    3 Pages
    1 2 3
    • Replies: 24
    • Views: 625
    Today, 05:41 PM Go to last post
    • Replies: 9
    • Views: 257
    Today, 05:32 PM Go to last post
  6. Poor man's induction heater power supply question.

    Started by DICKEYBIRD, 03-20-2019 03:18 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 657
    Today, 05:24 PM Go to last post
  7. help with square thread.

    Started by plunger, Yesterday 10:43 AM
    2 Pages
    1 2
    • Replies: 11
    • Views: 453
    Today, 05:17 PM Go to last post
  8. Project: Long road to a belt grinder

    Started by Cenedd, 03-20-2019 09:40 AM
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 992
    Today, 03:38 PM Go to last post
  9. O.T. the DIY Arborist

    Started by A.K. Boomer, Today 02:51 PM
    • Replies: 0
    • Views: 88
    Today, 02:51 PM Go to last post
  10. The Home Shop mentality... make vs drive and buy...

    Started by BCRider, 03-11-2019 02:01 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 38
    • Views: 2,100
    Today, 02:42 PM Go to last post
  11. OT cribbing for removing rear axle from junker?

    Started by metalmagpie, 03-23-2019 12:15 PM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 1,114
    Today, 02:19 PM Go to last post
  12. OT Carport post replacement steel vs wood

    Started by Mr Fixit, Today 11:45 AM
    • Replies: 8
    • Views: 183
    Today, 01:46 PM Go to last post
  13. Old lathe recognizing

    Started by don123, 01-14-2019 11:14 AM
    11 Pages
    1 2 3 ... 11
    • Replies: 105
    • Views: 8,319
    Today, 12:32 PM Go to last post
  14. Tail stock die holder project

    Started by markx, 03-21-2019 02:03 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 38
    • Views: 1,453
    Today, 12:06 PM Go to last post
  15. What did you machine today?

    Started by vpt, 04-20-2013 03:53 PM
    131 Pages
    1 2 3 ... 131
    • Replies: 1,305
    • Views: 451,890
    Today, 11:51 AM Go to last post
  16. the Viking Sky rescue

    Started by aostling, Yesterday 03:45 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 1,026
    Today, 11:17 AM Go to last post
  17. OT-Survey if your fingers DON'T crack

    Started by fixerdave, 03-08-2019 11:35 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 60
    • Views: 1,982
    Today, 09:53 AM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •