Page 1 of 16 12311 ... LastLast
Threads 1 to 20 of 307

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 01:30 AM
    344 Pages
    1 2 3 ... 344
    • Replies: 3,431
    • Views: 11,422,389
    Yesterday, 03:24 AM Go to last post
  2. Sticky Thread Sticky: Posting Photos and Starting Threads

    Started by George Bulliss, 01-28-2014 02:17 PM
    3 Pages
    1 2 3
    adding photos, photos
    • Replies: 22
    • Views: 59,810
    10-18-2018, 05:27 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 02:26 PM
    • Replies: 0
    • Views: 116,464
    04-21-2010, 02:26 PM Go to last post
  1. What did you do today?

    Started by vpt, 03-13-2010 08:56 PM
    168 Pages
    1 2 3 ... 168
    • Replies: 1,675
    • Views: 385,151
    Today, 10:06 AM Go to last post
  2. cut off saw questions

    Started by Abner, Today 09:17 AM
    • Replies: 5
    • Views: 26
    Today, 10:00 AM Go to last post
  3. Another gear question

    Started by elf, Today 01:57 AM
    • Replies: 3
    • Views: 69
    Today, 10:00 AM Go to last post
  4. Old Tool Catalogs

    Started by JRouche, 10-16-2018 08:17 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 747
    Today, 09:58 AM Go to last post
  5. Met a concrete post - car lost

    Started by Dunc, Yesterday 10:17 AM
    2 Pages
    1 2
    • Replies: 13
    • Views: 670
    Today, 09:52 AM Go to last post
  6. Where do I start?

    Started by Captain4W, Yesterday 04:05 PM
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 520
    Today, 09:51 AM Go to last post
  7. About that electric impact wrench, that does not work very well.

    Started by J Tiers, 10-16-2018 08:43 PM
    6 Pages
    1 2 3 ... 6
    • Replies: 51
    • Views: 1,325
    Today, 09:33 AM Go to last post
  8. China sent me an almost entire height gauge.

    Started by 1-800miner, Yesterday 10:31 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 304
    Today, 09:33 AM Go to last post
  9. Sunny 6x18 Surface Grinder

    Started by epicfail48, 09-17-2018 10:08 PM
    5 Pages
    1 2 3 ... 5
    • Replies: 40
    • Views: 2,342
    Today, 08:37 AM Go to last post
  10. Sherline, Logan, Southbend, Shedon, Atlas... Great hobby Lathes,

    Started by JRouche, 10-15-2018 12:54 AM
    7 Pages
    1 2 3 ... 7
    • Replies: 67
    • Views: 2,303
    Today, 06:37 AM Go to last post
  11. What happened to air tools?

    Started by Edwin Dirnbeck, 10-16-2018 08:59 AM
    5 Pages
    1 2 3 ... 5
    • Replies: 45
    • Views: 1,879
    Today, 05:14 AM Go to last post
  12. Lathe Tool suggestions for an old Newbie.

    Started by OaklandGB, 08-26-2018 11:39 AM
    15 Pages
    1 2 3 ... 15
    • Replies: 143
    • Views: 6,295
    Today, 02:42 AM Go to last post
  13. Question oldtiffie??????????

    Started by Guido, 10-15-2018 12:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 107
    • Views: 4,503
    Today, 01:43 AM Go to last post
    • Replies: 15
    • Views: 694
    Today, 12:31 AM Go to last post
  14. Over center manual cone clutch

    Started by brian Rupnow, 10-18-2018 12:48 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 475
    Yesterday, 10:27 PM Go to last post
  15. V4 engine, want to bore it out, tilt head or bob?

    Started by vpt, 10-14-2018 05:13 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 1,170
    Yesterday, 08:01 PM Go to last post
  16. First time firing up wood stove, no fan.

    Started by vpt, 10-17-2018 08:07 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 624
    Yesterday, 07:53 PM Go to last post
  17. OT, Someone ID this fitting

    Started by oxford, 10-18-2018 02:39 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 695
    Yesterday, 07:50 PM Go to last post
  18. metric threading gears

    Started by mudnducs, 10-17-2018 10:56 AM
    5 Pages
    1 2 3 ... 5
    • Replies: 41
    • Views: 1,155
    Yesterday, 07:35 PM Go to last post
    • Replies: 13
    • Views: 688
    Yesterday, 07:27 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •