Page 1 of 16 12311 ... LastLast
Threads 1 to 20 of 306

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 01:30 AM
    344 Pages
    1 2 3 ... 344
    • Replies: 3,431
    • Views: 11,421,725
    Yesterday, 03:24 AM Go to last post
  2. Sticky Thread Sticky: Posting Photos and Starting Threads

    Started by George Bulliss, 01-28-2014 02:17 PM
    3 Pages
    1 2 3
    adding photos, photos
    • Replies: 22
    • Views: 59,800
    10-18-2018, 05:27 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 02:26 PM
    • Replies: 0
    • Views: 116,462
    04-21-2010, 02:26 PM Go to last post
  1. China sent me an almost entire height gauge.

    Started by 1-800miner, Yesterday 10:31 PM
    • Replies: 7
    • Views: 128
    Today, 03:35 AM Go to last post
  2. About that electric impact wrench, that does not work very well.

    Started by J Tiers, 10-16-2018 08:43 PM
    5 Pages
    1 2 3 ... 5
    • Replies: 47
    • Views: 1,251
    Today, 03:27 AM Go to last post
  3. Where do I start?

    Started by Captain4W, Yesterday 04:05 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 379
    Today, 02:43 AM Go to last post
  4. Lathe Tool suggestions for an old Newbie.

    Started by OaklandGB, 08-26-2018 11:39 AM
    15 Pages
    1 2 3 ... 15
    • Replies: 143
    • Views: 6,249
    Today, 02:42 AM Go to last post
  5. Another gear question

    Started by elf, Today 01:57 AM
    • Replies: 0
    • Views: 10
    Today, 01:57 AM Go to last post
  6. Question oldtiffie??????????

    Started by Guido, 10-15-2018 12:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 107
    • Views: 4,429
    Today, 01:43 AM Go to last post
  7. What did you do today?

    Started by vpt, 03-13-2010 08:56 PM
    168 Pages
    1 2 3 ... 168
    • Replies: 1,673
    • Views: 384,947
    Today, 01:38 AM Go to last post
  8. Sherline, Logan, Southbend, Shedon, Atlas... Great hobby Lathes,

    Started by JRouche, 10-15-2018 12:54 AM
    7 Pages
    1 2 3 ... 7
    • Replies: 66
    • Views: 2,253
    Today, 01:38 AM Go to last post
  9. Met a concrete post - car lost

    Started by Dunc, Yesterday 10:17 AM
    2 Pages
    1 2
    • Replies: 11
    • Views: 565
    Today, 01:16 AM Go to last post
  10. Old Tool Catalogs

    Started by JRouche, 10-16-2018 08:17 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 724
    Today, 01:14 AM Go to last post
    • Replies: 15
    • Views: 664
    Today, 12:31 AM Go to last post
  11. Over center manual cone clutch

    Started by brian Rupnow, 10-18-2018 12:48 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 456
    Yesterday, 10:27 PM Go to last post
  12. V4 engine, want to bore it out, tilt head or bob?

    Started by vpt, 10-14-2018 05:13 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 1,156
    Yesterday, 08:01 PM Go to last post
  13. First time firing up wood stove, no fan.

    Started by vpt, 10-17-2018 08:07 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 609
    Yesterday, 07:53 PM Go to last post
  14. OT, Someone ID this fitting

    Started by oxford, 10-18-2018 02:39 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 672
    Yesterday, 07:50 PM Go to last post
  15. metric threading gears

    Started by mudnducs, 10-17-2018 10:56 AM
    5 Pages
    1 2 3 ... 5
    • Replies: 41
    • Views: 1,134
    Yesterday, 07:35 PM Go to last post
    • Replies: 13
    • Views: 650
    Yesterday, 07:27 PM Go to last post
  16. How does this clutch work?

    Started by brian Rupnow, 09-19-2018 03:44 PM
    9 Pages
    1 2 3 ... 9
    • Replies: 83
    • Views: 5,050
    Yesterday, 06:01 PM Go to last post
  17. General

    Started by knappdaddy3, 10-18-2018 05:30 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 615
    Yesterday, 03:51 PM Go to last post
  18. What did you machine today?

    Started by vpt, 04-20-2013 03:53 PM
    111 Pages
    1 2 3 ... 111
    • Replies: 1,108
    • Views: 397,670
    Yesterday, 02:00 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •