Page 1 of 18 12311 ... LastLast
Threads 1 to 20 of 344

Forum: General

This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.

  1. Sticky Thread Sticky: Shop Made Tools

    Started by bborr01, 01-20-2010 01:30 AM
    306 Pages
    1 2 3 ... 306
    • Replies: 3,054
    • Views: 10,231,847
    09-20-2017, 07:21 PM Go to last post
  2. Sticky Thread Sticky: Posting Photos

    Started by George Bulliss, 01-28-2014 02:17 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 40,908
    07-23-2017, 08:57 PM Go to last post
  3. Sticky Thread Sticky: Favorite Threads

    Started by George Bulliss, 04-21-2010 02:26 PM
    • Replies: 0
    • Views: 110,607
    04-21-2010, 02:26 PM Go to last post
  1. OT: SSD versus hard drive.

    Started by goose, 09-22-2017 05:19 PM
    3 Pages
    1 2 3
    • Replies: 26
    • Views: 1,046
    Today, 02:02 AM Go to last post
    • Replies: 3
    • Views: 45
    Today, 01:47 AM Go to last post
  2. OT- Equifax

    Started by Abner, 09-23-2017 09:09 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 37
    • Views: 908
    Today, 01:37 AM Go to last post
  3. OT?? hobby machinest in Oregon

    Started by gaston, Yesterday 01:04 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 301
    Today, 01:09 AM Go to last post
  4. Loft for storage in your shop for a midget?

    Started by 3 Phase Lightbulb, Yesterday 05:05 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 329
    Today, 01:03 AM Go to last post
  5. Are You a Laugher or a Thinker ???

    Started by Bob La Londe, Yesterday 11:34 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 422
    Today, 12:30 AM Go to last post
  6. lathe tailstock repair question.

    Started by Mr Fixit, 09-23-2017 12:18 PM
    • Replies: 9
    • Views: 411
    Today, 12:19 AM Go to last post
  7. Npt questions about tightening and sealing

    Started by challenger, Yesterday 01:20 PM
    • Replies: 8
    • Views: 245
    Today, 12:14 AM Go to last post
  8. What did you machine today?

    Started by vpt, 04-20-2013 03:53 PM
    64 Pages
    1 2 3 ... 64
    • Replies: 639
    • Views: 233,547
    Yesterday, 11:57 PM Go to last post
  9. Disaster in Dayton... End of an Era... Je suis désolé

    Started by Dan_the_Chemist, 09-23-2017 08:57 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 891
    Yesterday, 11:56 PM Go to last post
  10. can you use a surface grinder on aluminum?

    Started by mudnducs, 09-21-2017 10:01 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 842
    Yesterday, 10:54 PM Go to last post
  11. so what's the verdict on the picture thing?

    Started by A.K. Boomer, 09-06-2017 02:13 PM
    19 Pages
    1 2 3 ... 19
    • Replies: 185
    • Views: 7,760
    Yesterday, 09:55 PM Go to last post
  12. Why does it matter where jaws go on 4 jaw (or does it matter)?

    Started by softtail, Yesterday 10:06 AM
    2 Pages
    1 2
    • Replies: 13
    • Views: 529
    Yesterday, 09:51 PM Go to last post
  13. Looking to drill a small hole- 94 gauge (.007 in, .180mm)….

    Started by DS_park, Yesterday 09:58 AM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 510
    Yesterday, 09:01 PM Go to last post
  14. machining a "D" profile

    Started by restorick, Yesterday 07:08 AM
    2 Pages
    1 2
    • Replies: 18
    • Views: 656
    Yesterday, 08:42 PM Go to last post
    • Replies: 8
    • Views: 348
    Yesterday, 05:16 PM Go to last post
  15. OT: Carry Smartphone in Shop / Job Site?

    Started by Fasttrack, 09-22-2017 10:46 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 31
    • Views: 1,194
    Yesterday, 05:12 PM Go to last post
  16. Back to Steam--

    Started by brian Rupnow, 09-04-2017 04:09 PM
    13 Pages
    1 2 3 ... 13
    • Replies: 126
    • Views: 8,734
    Yesterday, 04:47 PM Go to last post
  17. Atlas Lathe Upgrade

    Started by Be_Zero_Be, 09-18-2017 02:10 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 583
    Yesterday, 02:51 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •