Register
Help
Remember Me?
What's New?
Forum
New Posts
FAQ
Calendar
Community
Groups
Albums
Forum Actions
Mark Forums Read
Quick Links
Today's Posts
View Site Leaders
Advanced Search
2ManyHobbies
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
2ManyHobbies
Senior Member
Find latest posts
Find latest started threads
Mini Statistics
Join Date
10-18-2007
Last Activity
Yesterday
11:04 AM
Tab Content
2ManyHobbies's Activity
About Me
Tab Content
All
2ManyHobbies
Friends
Photos
New Activity (
)
Older Activity
05-16-2013,
02:00 PM
2ManyHobbies
replied to a thread
Enlarging holes
in
General
Definitely clamp vertically and make a material and spacer sandwich then.
see more
54 replies | 3639 view(s)
05-16-2013,
01:49 PM
2ManyHobbies
replied to a thread
Enlarging holes
in
General
To expound on that a little further... This is putting a 44mm hole through a 4mm thickness over a 100mm unsupported span. Treat it as a thin...
see more
54 replies | 3639 view(s)
05-16-2013,
01:38 PM
2ManyHobbies
replied to a thread
Enlarging holes
in
General
This isn't a boring operation. This is a trepanning operation. Clamp vertically and trepan between the clamps. If you still want to stick with...
see more
54 replies | 3639 view(s)
04-16-2013,
02:51 PM
2ManyHobbies
replied to a thread
The "Almost" Flood---
in
General
Assuming there is a lower place somewhere nearby, a siphon could work in an emergency. Any sort of human-powered pump with a check valve could...
see more
39 replies | 2937 view(s)
03-20-2013,
10:42 AM
2ManyHobbies
replied to a thread
OT: Interesting electronic part...... 3000F capacitor
in
General
It doesn't look like much, but charged, it'd have the equivalent of the energy in 56 grains of gun powder.
see more
21 replies | 1616 view(s)
03-12-2013,
04:12 PM
2ManyHobbies
replied to a thread
Stock too long for lathe bed. What to do!
in
General
Take a tubing cutter and replace the cutter with a roller. Use clamps to hold a parting tool to the side of the cutter body (adjust as needed). ...
see more
27 replies | 2830 view(s)
03-02-2013,
08:56 AM
2ManyHobbies
replied to a thread
Enco Milling machine and lathe ideas
in
General
Any idea how heavy on each machine? Under 250 lbs, use a hand truck. Under a half ton, you could use an engine hoist. Lift, put some...
see more
12 replies | 820 view(s)
03-01-2013,
09:34 AM
2ManyHobbies
replied to a thread
From Shaving to Murder; Why People Should Have Their Throats Slashed
in
General
I've got the honing and shaving down. I'm looking at grinding new razors from stock. The wife likes the straight razor as well, so I'm honing almost...
see more
80 replies | 6753 view(s)
02-28-2013,
06:45 PM
2ManyHobbies
replied to a thread
From Shaving to Murder; Why People Should Have Their Throats Slashed
in
General
I started shaving with a straight razor as an attempt to address ingrown hairs. It worked wonders and I think I spend maybe a few bucks a year on...
see more
80 replies | 6753 view(s)
More Activity
No More Results
About 2ManyHobbies
Basic Information
Statistics
Total Posts
Total Posts
504
Posts Per Day
0.25
General Information
Last Activity
Yesterday
11:04 AM
Join Date
10-18-2007
Referrals
0
Find latest posts