Tab Content
  • rolland's Avatar
    05-17-2015, 06:50 PM
    Does anyone here that restore old cars also work on the on old electro/mechanical voltage regulators? I know there are a lot of restorers out there...
    0 replies | 186 view(s)
  • rolland's Avatar
    05-15-2015, 10:03 PM
    rolland replied to a thread Treadmill motor question in General
    Thank you for the information, understand now.
    23 replies | 1559 view(s)
  • rolland's Avatar
    05-15-2015, 05:58 PM
    rolland replied to a thread Treadmill motor question in General
    Ok Max What is the difference between linear and logarithmic pots??? Try to keep it simple I don't delve into this world very often, actually not at...
    23 replies | 1559 view(s)
  • rolland's Avatar
    05-15-2015, 02:41 PM
    rolland replied to a thread Treadmill motor question in General
    Mike I will I will I am so excited!!!! you see I am an analog person stuck in the digital world. I remember when the house had only one phone and it...
    23 replies | 1559 view(s)
  • rolland's Avatar
    05-15-2015, 01:07 AM
    rolland replied to a thread Treadmill motor question in General
    I had been asking questions on the wiring on these motors and controllers as I really have not worked with this type of motor control and wanted a...
    23 replies | 1559 view(s)
  • rolland's Avatar
    05-14-2015, 03:40 PM
    rolland replied to a thread Treadmill motor question in General
    Max You just went waaaaay over my head would you care to explain further???
    23 replies | 1559 view(s)
  • rolland's Avatar
    05-13-2015, 11:01 PM
    rolland replied to a thread Treadmill motor question in General
    I didn't include a picture of the board but it is marked an MC-60
    23 replies | 1559 view(s)
  • rolland's Avatar
    05-13-2015, 07:51 PM
    rolland replied to a thread Treadmill motor question in General
    Well I am now swimming with the sharks, I have removed all the necessary parts for making a new drive system and need some help putting it back in...
    23 replies | 1559 view(s)
  • rolland's Avatar
    05-13-2015, 04:49 AM
    rolland replied to a thread Vertical Mill in Gunsmithing
    I have a G3103 mill I bought 8 years ago. It is an ok size for pistol and action but the bed is too short for much barrel work. It is the smallest I...
    19 replies | 1101 view(s)
  • rolland's Avatar
    05-12-2015, 01:20 AM
    rolland replied to a thread Treadmill motor question in General
    Dennis I like the write up but can't download the pdf can you send it another way?
    23 replies | 1559 view(s)
  • rolland's Avatar
    05-10-2015, 10:39 PM
    I have become the proud owner of a Lifestyle 550 treadmill in working condition. Since I am in the best shape I am going to be for the rest of my...
    23 replies | 1559 view(s)
  • rolland's Avatar
    04-30-2015, 08:50 PM
    Rosco Thanks that was the one I needed
    2 replies | 532 view(s)
  • rolland's Avatar
    04-30-2015, 12:09 AM
    I remember reading a post on reversing the index plate on a spin index but am unable to locate it could someone help me find it or remember where I...
    2 replies | 532 view(s)
  • rolland's Avatar
    04-21-2015, 11:06 PM
    I did not see a reference to the G4003 the green one standard lathe but I just checked mine and it has the same problem Thanks for bringing this to...
    24 replies | 4668 view(s)
  • rolland's Avatar
    04-17-2015, 07:18 PM
    rolland replied to a thread rheostat help in General
    I bought a controller off of ebay that will work for my small motor. The price was less than $5 shipped from China, its no wonder we can't compete in...
    15 replies | 1518 view(s)
  • rolland's Avatar
    04-06-2015, 11:03 PM
    rolland replied to a thread rheostat help in General
    Found one on ebay that fits my needs.
    15 replies | 1518 view(s)
  • rolland's Avatar
    04-05-2015, 11:55 PM
    rolland replied to a thread rheostat help in General
    Thanks for the sites I will work on getting something that will work for what I am doing.
    15 replies | 1518 view(s)
  • rolland's Avatar
    04-05-2015, 10:22 PM
    rolland replied to a thread rheostat help in General
    Paul When I stopped messing with these things we called them rheostats, so that should give you the reason why I posted this. I still have a hard...
    15 replies | 1518 view(s)
  • rolland's Avatar
    04-05-2015, 10:01 PM
    rolland started a thread rheostat help in General
    I need a rheostat to run a small 24vdc gear motor. I power it off of a 70W 120/24vdc supply. I use it as a turntable to paint items but at 45 rpm its...
    15 replies | 1518 view(s)
  • rolland's Avatar
    03-19-2015, 08:14 PM
    rolland replied to a thread Looking for Swiss files in General
    Thanks for all the responses, I have been to most all those web sites but not finding what I want. I will contact Boggs Tool tomorrow and see if he...
    10 replies | 1140 view(s)
  • rolland's Avatar
    03-19-2015, 03:34 AM
    I bought a set of Habilis files a number of years ago and am looking for a finer cut either #3 or #4 or both. The ones I have are #1 and from what I...
    10 replies | 1140 view(s)
No More Results
About rolland

Basic Information

About rolland
Location:
Arizona

Statistics


Total Posts
Total Posts
300
Posts Per Day
0.11
General Information
Last Activity
Yesterday 11:08 PM
Join Date
02-18-2008
Referrals
0