CCWKen
Senior Member

Is this a one-off run or for production? You could use one of the Phenol Novolac Epoxies. These epoxies are gas, oil and solvent resistant. If...

The start capacitor is probably bad. I had the same problem with my old Craftsman band saw. A new capacitor made it like new.

Almost looks like a small version of my 30t Toledo OBI.

Does it throw the blade just running or when you try to cut something. Check the guides too. Sounds like it may be a worn/loose bearing causing poor...

I don't think they'll let me post it here. :)

Nice repair job. My field cutters are covered in patches and fixes. :)

Four inches is standard but there's more to it than that. There's a big difference between 1500psi concrete watered down for flow that some...

That's about what they are in the deep south too. I don't see anything way out of line. A worn out J-Model BP can bring an easy $4000 and up down...

Cutting on the down stroke is what keeps the part on the table. :)

Most window motors are wired with a 10-25A fuse or breaker. It depends on the application and motor. I would guess a small motor would draw about...

AVG is crap. I diagnose so many BSODs caused by AVG it's a wonder they stay around. It also uses 6-7 drivers to operate. Way too much bloat....

My worst was a 1969 Ford Cortina (English Ford). Great mileage and plenty of pep but lousy in rain or snow. Too light and no traction.

I strung or buried every wire on my property except the ones from the transformers to my service poles (two meters). The only permit I had to get...

I have a bench top Clipper belt lacer (two handles) but since no one knows where you are, suggesting where to get or borrow one is a goose chase. :(

Looks like I'm not the only one for sure. We must have been typing at the same time Gary. :)

I have a small box full of loose jaws but have no idea what they might fit. They don't fit the chucks I have and they aren't marked. These came with...

I suppose it depends in what part of world you are. PCV pipe won't last even five years in the open down here. It turns brown and become very...

$20 wouldn't repair a transistor radio these days. Check the fuse in the power supply module. You might get lucky. If you have to buy any modules or...

A/C refrigerant tanks might work too. They're a little smaller than a propane tank. The salvage yard down here is full of them. The problem is that...

I have an old water heater tank I patched and use for an air accumulator/drier on the sand blasting compressor. The compressor is only about 120psi...

Boron nitride is the primary ingredient in most spray-on high-temp mold releases. Works good too and doesn't take a lot to get coverage. When the...

I use the one below in my Favorites Bar. It takes me to the first page of the General forum. If I want the others, I just click on Forum at the top...

Every OEM machine has burdensome "Bloatware" preloaded. The best thing to do when buying a new store-bought machine is to do a clean install of the...

My nephew was visiting a couple of weeks ago and happened to use his phone GPS app. He was able to zoom in and it showed his location sitting on the...

I was running IE8 for a couple of years and just recently installed IE10. I thought I would have to export then import all my favorites and tracking...

I made one about 4 1/2" in diameter out of 1" plate. It was a quick and dirty so not the precision of Dave's. But hey, it was for turning starter and...

IE10 is installed as an update. Go to Installed Updates and uninstall it there. Windows will revert back to the previous version.

Yeah, I don't think he's that old. :)

Looks great Guido! After I retire for the second time, I'm going to build this 1951 Chrysler K-310. I already have a 51 Imperial for the donor...

You'll need to do some shrinking to roll up the edges. If you post some pictures of the part, perhaps more detail help can be given. Or just send the...