View Profile: Edwin Dirnbeck - The Home Shop Machinist & Machinist's Workshop Magazine's BBS

Tab Content: All; Edwin Dirnbeck; Friends; Photos

Older Activity
04-30-2013, 08:14 PM

Edwin Dirnbeck replied to a thread Bush hog repair in General

This is a very nice job that you did.How did you cut the opening so smooth and straight.My torch cuts allways look like they were done with a...

see more

19 replies | 1387 view(s)
04-16-2013, 11:08 AM

Edwin Dirnbeck replied to a thread Air hammer modification in General

Google Michigan air hammer or single hit air chisel.They list a number of single shot air hammers.

see more

11 replies | 1159 view(s)
04-16-2013, 09:36 AM

Edwin Dirnbeck started a thread A question about youtube videos in General

I was looking at engine lathe videos on you tube .There are over 65,000 of them ,so as I am going to the next page I notice that the page numbers are...

see more

1 replies | 278 view(s)
04-10-2013, 03:10 PM

Edwin Dirnbeck started a thread 1949 Mercury dwarf car in General

I dont know how to make a video appear in this thread ,but if you google 1949 mercury dwarf car it comes right up.At first I thought this was video...

see more

4 replies | 407 view(s)
03-22-2013, 09:48 AM

Edwin Dirnbeck replied to a thread Why so down on lantern toolposts? in General

When I was a youngster ,I used a rocker, lantern toolpost for about 10 years full time in a high pressure job shop setting.I swore that some day I...

see more

37 replies | 3622 view(s)
03-19-2013, 08:45 AM

Edwin Dirnbeck replied to a thread dovetail supplier in General

It sounds as if you are trying to make a quick change repeatable conection to your product holding fixture. If so maby you could modify an aloris...

see more

8 replies | 698 view(s)
03-18-2013, 03:01 PM

Edwin Dirnbeck replied to a thread Chamfering tool for flat socket head screws in General

If you are going to use these screws you will get a much nicer looking job if you have a specific size countersink for each screw size.What I did was...

see more

13 replies | 1362 view(s)
03-16-2013, 10:37 AM

Edwin Dirnbeck replied to a thread Ggzzzht! in General

PUT GROUND PRONG UP.I cant for the life of me under stand why the electric codes dont DEMAND that the ground prong MUST be UP when instaling ...

see more

37 replies | 2316 view(s)
03-13-2013, 07:26 PM

Edwin Dirnbeck replied to a thread Insert angles in General

You are absolutly correct. If you google tng toolholder or tnmg toolholder,you can look at images that show the angle

see more

12 replies | 869 view(s)
03-12-2013, 08:46 AM

Edwin Dirnbeck replied to a thread What's you're favorite cutting fluid in General

Mineral oil. My all purpose oil for EVERYTHING is crystal clear non smellinG mineral oil .I buy it at the farm supply store ,farmers use it to rub on...

see more

16 replies | 1643 view(s)
03-11-2013, 08:27 PM

Edwin Dirnbeck replied to a thread Another paint thread with questions in General

I have made many pieces of equipment look very presentable using gloss LATEX paint from the local hardware store or the big box store.The best part...

see more

19 replies | 1150 view(s)
03-05-2013, 09:23 PM

Edwin Dirnbeck replied to a thread off-center (?) turning with the 4-jaw in General

Mount your indicater on your tool post, indicate the high end,move caraidge away, rotate 180 degree put apropriate gage block build up on low end,...

see more

11 replies | 1004 view(s)

No More Results

Edwin Dirnbeck
Member

Mini Statistics

Basic Information

Statistics

Total Posts

General Information

Edwin Dirnbeck Member

Mini Statistics

Basic Information

Statistics

Total Posts

General Information

Edwin Dirnbeck
Member