Tab Content
rws's Activity
About Me
Tab Content
  • rws's Avatar
    Yesterday, 06:39 PM
    Back when I worked for contractors, we send to send regulators to the air/gas supplier for rebuilds. Somebody has parts for them. And they can’t be...
    8 replies | 186 view(s)
  • rws's Avatar
    12-11-2018, 06:19 PM
    rws replied to a thread Turning a long taper in General
    In the post by old mart with the eBay link, I would be interested in making one available f it had a l8ve center not dead center. Is there a live...
    33 replies | 1379 view(s)
  • rws's Avatar
    12-11-2018, 06:15 PM
    rws replied to a thread Glue For Neoprene Rubber in General
    Try that yellow goop for gluing weatherstripping on cars. Messy but works.
    39 replies | 1118 view(s)
  • rws's Avatar
    12-05-2018, 12:31 PM
    Yes the big pipe is plenty long enough to support the smaller pipe. I thought about turning a filler ring or two. possibility. Getting welding leads...
    15 replies | 694 view(s)
  • rws's Avatar
    12-05-2018, 10:51 AM
    I'm having a mental block here, seems this should be simple but it's just passing my by. I have an unused satellite mount on my roof, a 3 legged one...
    15 replies | 694 view(s)
  • rws's Avatar
    11-25-2018, 10:37 AM
    rws replied to a thread OT- Heat Pump ? in General
    Well, where I live the ground is shale, kinda hard to dig through it without major equipment. Where I work, the County puts in a lot of geothermal...
    5 replies | 371 view(s)
  • rws's Avatar
    11-24-2018, 05:44 PM
    rws started a thread OT- Heat Pump ? in General
    My unit s but a couple years old. I have a temp,probe in the supply duct right above the air handler, and I keep an eye on supply temps. Over the...
    5 replies | 371 view(s)
  • rws's Avatar
    11-21-2018, 05:32 AM
    rws replied to a thread OT- Ice Maker Issue in General
    Well, it kicked in and is making ice and cycling fine. The cubes (half rounds) are a bit smaller than before but it is working. In the past, when the...
    12 replies | 541 view(s)
  • rws's Avatar
    11-20-2018, 07:07 PM
    rws replied to a thread OT- Ice Maker Issue in General
    Yes the bar is down, so I’ll wait until tomorrow. Thanks.
    12 replies | 541 view(s)
  • rws's Avatar
    11-20-2018, 06:16 PM
    rws started a thread OT- Ice Maker Issue in General
    The ice maker in my frig quit a couple weeks ago. Since the frig is 14 years old, I figured the ice maker unit just gave up. So I ordered a...
    12 replies | 541 view(s)
  • rws's Avatar
    11-16-2018, 05:54 PM
    I know nothing about forging, but I watch Forged In Fire. Someone tried to water quench W-1, and the blade warped. The judges all said don’t do it,...
    35 replies | 1914 view(s)
  • rws's Avatar
    11-03-2018, 07:29 AM
    rws started a thread OT- Smart Phone Apps in General
    I have a no-name phone from a popular provider. A phone to me is for calls and now texts, web browsing wasn’t on my radar. The phone came loaded with...
    7 replies | 403 view(s)
  • rws's Avatar
    10-24-2018, 06:05 PM
    rws replied to a thread OT- WiFi Range Extender in General
    Yes it does, something like up to 10. These sound pretty good!
    7 replies | 613 view(s)
  • rws's Avatar
    10-24-2018, 08:26 AM
    rws started a thread OT- WiFi Range Extender in General
    We use a mobile hotspot for our internet, there is no cable available. The hotspot is close to a window to get it's signal, and it's OK for the...
    7 replies | 613 view(s)
  • rws's Avatar
    10-24-2018, 06:41 AM
    OK, here is a pic of the gate. I guess the fixes have pretty much been discussed. I'm thinking of replacing the rod along the top of the gates...
    15 replies | 1006 view(s)
  • rws's Avatar
    10-23-2018, 11:37 AM
    I will this afternoon and post it tomorrow. I didn't plan on making this post until I get an email from my wife expressing her frustrations of...
    15 replies | 1006 view(s)
  • rws's Avatar
    10-23-2018, 11:36 AM
    Well, to be honest, I made an error when I sunk the posts, hence the gap. However, that gap is no wider than the spacing of the pipes, so I left it...
    15 replies | 1006 view(s)
  • rws's Avatar
    10-23-2018, 08:19 AM
    I have two metal "farm" gates across my driveway, they close with a gap of about 5". It's a gravel driveway so using a cane bolt would be a constant...
    15 replies | 1006 view(s)
  • rws's Avatar
    10-06-2018, 07:47 AM
    rws started a thread CO 2 Tanks in Home Shop Welding
    I have always used flux core wire with my MIG. I see a local CL ad selling 2 CO-2 tanks, but says they need to be hydro’d before refilling. Is this...
    5 replies | 770 view(s)
  • rws's Avatar
    09-27-2018, 01:06 PM
    I would get a box scraper, then change the top link and adjustable down link (3 point hitch) to hydraulic cylinders. Then you can adjust all you need...
    19 replies | 1336 view(s)
  • rws's Avatar
    09-21-2018, 06:26 PM
    rws replied to a thread Nardini...yeah, well, but in General
    Yeah, I was thinking we were only seeing a part of the big boy. The Nardini is well used. Long headstock too.
    19 replies | 1529 view(s)
No More Results
About rws

Basic Information

About rws
Location:
Virginia

Statistics


Total Posts
Total Posts
1,169
Posts Per Day
0.21
General Information
Last Activity
Yesterday 06:40 PM
Join Date
11-03-2003
Referrals
0