Tab Content
  • radkins's Avatar
    Yesterday, 10:10 AM
    radkins replied to a thread coating on brass in General
    As is any oxidation or any other surface contaminate, although the oxidation will eventually return, so it could be that the acid left you with an...
    11 replies | 593 view(s)
  • radkins's Avatar
    Yesterday, 10:08 AM
    radkins replied to a thread coating on brass in General
    Not at all, it simply went under the coating and dissolved the metal at the point of adhesion, acid will not do anything much to a plastic type...
    11 replies | 593 view(s)
  • radkins's Avatar
    03-28-2017, 11:19 AM
    radkins replied to a thread coating on brass in General
    Much better than using acid, which likely had little if any effect on the actual coating, would have been paint remover, Tal-Strip or similar....
    11 replies | 593 view(s)
  • radkins's Avatar
    03-26-2017, 04:00 PM
    Yep you are 100% correct but even after 30 years these things have been around it is amazing how many folks simple will not believe this! Just...
    8 replies | 250 view(s)
  • radkins's Avatar
    03-20-2017, 10:06 AM
    Welders are a different breed for sure and we liked our fun! Joking aside, fun is one thing but on a serious note horse play and apathy toward the...
    34 replies | 7307 view(s)
  • radkins's Avatar
    03-19-2017, 05:31 PM
    Sounds like almost as much fun as taking the piece of dark cardboard that usually comes under a candy bar and slipping it under the dark lens in a...
    34 replies | 7307 view(s)
  • radkins's Avatar
    03-14-2017, 02:23 PM
    I am not going to flat out disagree with you because my opinion is just that, my opinion. However personally I absolutely detest those things...
    11 replies | 639 view(s)
  • radkins's Avatar
    03-14-2017, 11:13 AM
    I probably should have mentioned that the only thing I will be using the brass/bronze for would be the actual receiver itself, everything else will...
    23 replies | 1818 view(s)
  • radkins's Avatar
    03-13-2017, 10:25 PM
    As long as the steel does not require a low hydrogen rod then 7018 will work just fine without being stabilized in an oven, of course you wouldn't...
    11 replies | 639 view(s)
  • radkins's Avatar
    03-13-2017, 08:50 PM
    I just watched that video and something doesn't look right here, with the cover off that looks like brass the receiver itself is made of but the one...
    23 replies | 1818 view(s)
  • radkins's Avatar
    03-13-2017, 07:46 PM
    Actually I like them a lot and I can even reassemble one!!! :D
    23 replies | 1818 view(s)
  • radkins's Avatar
    03-13-2017, 06:22 PM
    Wow, thanks Bob you just provided the answers to the specs I have been searching on the 'net for, all in one neat group! Some of that, most probably,...
    23 replies | 1818 view(s)
  • radkins's Avatar
    03-13-2017, 01:43 PM
    Hope you guys aren't getting tired of my dwelling on this subject but now something else has me scratching my head -AGAIN, good thing us grizzled old...
    23 replies | 1818 view(s)
  • radkins's Avatar
    03-13-2017, 10:35 AM
    Just from searching the 'net and also just yesterday in a gun magazine I thumbed through at Walmart (I don't remember the name but it is currently on...
    23 replies | 1818 view(s)
  • radkins's Avatar
    03-12-2017, 07:34 PM
    Well I have spent several hours researching this and I have found a few surprising things and some not so surprising, it looks as if Yondering and I...
    23 replies | 1818 view(s)
  • radkins's Avatar
    03-11-2017, 12:22 PM
    Ok, I have been brass shopping and as I suspected I came away confused, :confused: While I have learned a bit about brass and bronze the only...
    23 replies | 1818 view(s)
  • radkins's Avatar
    03-11-2017, 11:25 AM
    Certainly no flaming as that is a completely legitimate question, and unfortunately (for me) one that I can answer from recent experience. Victor...
    8 replies | 1058 view(s)
  • radkins's Avatar
    03-11-2017, 09:25 AM
    I have been told, but didn't know for certain, that the Henry rifles are actually steel with nonfunctional brass plates covering the steel ??? ...
    23 replies | 1818 view(s)
  • radkins's Avatar
    03-10-2017, 01:00 PM
    I have some hard brass and have been thinking of making a brass rifle receiver based on the scaled down "Baby" 1885 Highwall single shot rifle that I...
    23 replies | 1818 view(s)
  • radkins's Avatar
    02-02-2017, 02:53 PM
    Yes I cleaned it thoroughly but there was very little contamination since both sides is coated with a rather heavy and soft plastic film, I trimmed...
    59 replies | 4082 view(s)
  • radkins's Avatar
    02-02-2017, 01:05 PM
    Thanks for all the info, just to update here -it worked (so far anyway). The caps were about 25 years old in a 1991 Ford F150 PCM (PCM=Powertrain...
    59 replies | 4082 view(s)
  • radkins's Avatar
    02-01-2017, 06:22 PM
    I need to replace two capacitors on a circuit board so I took the specs from the old ones (47uf, 16v 105C) and ordered a bunch of new ones. Ok so the...
    59 replies | 4082 view(s)
No More Results
About radkins

Basic Information

About radkins
Location:
Central Kentucky

Statistics


Total Posts
Total Posts
2,711
Posts Per Day
0.87
General Information
Last Activity
Yesterday 04:22 PM
Join Date
09-17-2008
Referrals
0