Tab Content
  • dlsinak's Avatar
    04-18-2015, 04:42 PM
    dlsinak replied to a thread OT Stuck on Alloy Wheels in General
    Try a mix of 50/50 ATF & acetone. Astounding penetrating oil:)
    94 replies | 5039 view(s)
  • dlsinak's Avatar
    04-14-2015, 01:53 AM
    I actually just found a marking on the chuck " #33 taper " which I have never heard of. Some more research is in my future. Dennis
    7 replies | 556 view(s)
  • dlsinak's Avatar
    04-13-2015, 08:11 PM
    I just got a Rockwell 15" drill press, found it on CraigsList. The ad said it needed a new motor, I have a Rockwell motor, so I went to get it. ...
    7 replies | 556 view(s)
  • dlsinak's Avatar
    04-08-2015, 03:41 PM
    I put new shocks on BMW 1150gs. They were taller than stock and when my bike was loaded, it would fall over when I used the kickstand. I just...
    9 replies | 983 view(s)
  • dlsinak's Avatar
    04-07-2015, 01:55 AM
    dlsinak started a thread RPMs and Feed Rates? in General
    I was looking thru my old issues of HSM and MW and I came upon an article about spindle speeds, work diameter and all the various factors for correct...
    4 replies | 412 view(s)
  • dlsinak's Avatar
    03-30-2015, 01:23 AM
    dlsinak started a thread 4 Jaw Chuck Question in General
    I have a 4 jaw chuck that came with my Jet lathe. One of the jaws is extremely tight to move. On close examination, there is a retainer pin that must...
    3 replies | 372 view(s)
  • dlsinak's Avatar
    03-28-2015, 10:52 AM
    dlsinak replied to a thread Keyless Chuck Issue in General
    Cleaned it and lightly oiled, seems to work OK now, but I do have a new chuck on the way.
    18 replies | 1330 view(s)
  • dlsinak's Avatar
    03-27-2015, 06:16 PM
    dlsinak replied to a thread Keyless Chuck Issue in General
    I've not oiled it or greased it at all. I made sure that the center drill was not bottomed out also.
    18 replies | 1330 view(s)
  • dlsinak's Avatar
    03-27-2015, 04:25 PM
    dlsinak replied to a thread Keyless Chuck Issue in General
    I'm not sure of the brand, I can't see any markings. I've tried using the spindle brake and the knurled ring and using either seems to be equal...
    18 replies | 1330 view(s)
  • dlsinak's Avatar
    03-27-2015, 03:40 PM
    dlsinak started a thread Keyless Chuck Issue in General
    I have a keyless chuck to use in my mill. I was using it yesterday with a center drill and the center drill came loose, as in it stopped while the...
    18 replies | 1330 view(s)
  • dlsinak's Avatar
    03-18-2015, 06:10 PM
    dlsinak replied to a thread Ordering Small Tools, etc in General
    Yes I do live in Anchorage. I will try calling the various companies to ask if they will ship via USPS as most everything I want will fir in a...
    7 replies | 801 view(s)
  • dlsinak's Avatar
    03-18-2015, 03:07 PM
    Living in Alaska, ordering things is no problem, but the cost of shipping is a problem. USPS Priority is usually the least expensive. I have found...
    7 replies | 801 view(s)
  • dlsinak's Avatar
    03-12-2015, 03:19 PM
    Thanks for sharing the link. It just goes to prove, "you don't know what you don't know, and you don't know that you don't know what you don't know."...
    35 replies | 4279 view(s)
  • dlsinak's Avatar
    02-16-2015, 11:27 PM
    dlsinak replied to a thread Jet GHB 1340 Lathe Manual in General
    I just sent you a PM. Thanks a bunch! Dennis
    6 replies | 365 view(s)
  • dlsinak's Avatar
    02-16-2015, 09:32 PM
    dlsinak replied to a thread Jet GHB 1340 Lathe Manual in General
    Thanks, I suspected that a little brute force is necessary. ;)
    6 replies | 365 view(s)
  • dlsinak's Avatar
    02-16-2015, 07:42 PM
    Can someone direct me to where I can get a copy of the operator's manual for my Jet GHB 1340 lathe? I cannot for the life of me get the three jaw...
    6 replies | 365 view(s)
No More Results
About dlsinak

Basic Information

About dlsinak
Location:
Anchorage, AK

Statistics


Total Posts
Total Posts
123
Posts Per Day
0.05
General Information
Last Activity
Yesterday 01:44 AM
Join Date
10-03-2008
Referrals
0