Tab Content
  • oxford's Avatar
    02-14-2019, 02:36 PM
    No help for you but 1/2-28 is the common thread for ar15 barrels. Edit, I need better reading skills. OP is talking 12-28 not 1/2-28.
    32 replies | 1431 view(s)
  • oxford's Avatar
    02-13-2019, 09:49 AM
    oxford replied to a thread Mill vice back saver stand in General
    I have seen some pictures of some pretty slick setups over the years. I know there were a few with 2 hooks/arms. One for the vise and one for a...
    13 replies | 618 view(s)
  • oxford's Avatar
    02-10-2019, 09:15 PM
    Looks good. You may have been able to save a little time by turning the OD first and then boring the OD size into a set of soft jaws on the mill and...
    31 replies | 1391 view(s)
  • oxford's Avatar
    02-06-2019, 10:11 PM
    This. If you can get an 1/8” of play it sounds like there is something in the front getting hung up.
    8 replies | 300 view(s)
  • oxford's Avatar
    02-06-2019, 08:42 PM
    Ok, first off what model Clausing lathe are we talking about? Second, I have always used an outside picture hosting site to post pictures here. ...
    8 replies | 300 view(s)
  • oxford's Avatar
    01-30-2019, 11:53 AM
    I don’t know, if you break it down is it really one project? Is the guy that bought car “a” and put headers and a cam in it then sold it and bought...
    30 replies | 1875 view(s)
  • oxford's Avatar
    01-27-2019, 08:06 PM
    oxford replied to a thread I wanna tap that !!! in General
    I have used these in the past, mostly 10-24 on tubing. They do cut down on time quite a bit but require a little finesse. You have to be careful of...
    50 replies | 1758 view(s)
  • oxford's Avatar
    01-27-2019, 07:24 PM
    oxford replied to a thread I wanna tap that !!! in General
    The sprial point taps do ok on blind holes as long as you can drill the hole deeper than what your intended tap depth is(drill it deep enough so the...
    50 replies | 1758 view(s)
  • oxford's Avatar
    01-27-2019, 06:56 PM
    oxford replied to a thread I wanna tap that !!! in General
    If you don’t have the plate yet and really have hundreds of holes to tap in a 45”x68” piece I would consider getting some quotes on having the plate...
    50 replies | 1758 view(s)
  • oxford's Avatar
    01-27-2019, 05:28 PM
    oxford replied to a thread I wanna tap that !!! in General
    I have tapped hundreds if not thousands of holes with a hand drill, I have also broke my share of taps doing it. If through holes and above 1/4” it...
    50 replies | 1758 view(s)
  • oxford's Avatar
    01-26-2019, 07:14 PM
    Says the guy with a CNC mill.:rolleyes: A manual one would have been cheaper. A file, cheaper yet.
    31 replies | 1439 view(s)
  • oxford's Avatar
    01-26-2019, 07:08 PM
    You could always stock up on a few cans of the compressed air electronic cleaner or air duster.
    31 replies | 1439 view(s)
  • oxford's Avatar
    01-22-2019, 08:45 PM
    If you think you will be doing any amount of small bar or round you can cut grooves into the ends of the rolls to keep things straight. My big slip...
    181 replies | 58254 view(s)
  • oxford's Avatar
    01-20-2019, 04:37 PM
    oxford replied to a thread Slip roll question. in General
    That should not be a problem rolling that. I have never tried to put a cone back into the rollers, it may get tricky. It wouldn’t be hard to turn a...
    10 replies | 475 view(s)
  • oxford's Avatar
    01-19-2019, 05:31 PM
    oxford replied to a thread Humidifier Help If Possible in General
    Does that one use a filter? We have had some that did, not sure if they can get bad enough to make it stop working though.
    15 replies | 590 view(s)
  • oxford's Avatar
    01-15-2019, 09:18 PM
    If you roll a complete ring how do you get it out? The way it looks now is to unscrew the 4 top bolts and then lift the top roller out with the...
    181 replies | 58254 view(s)
  • oxford's Avatar
    01-13-2019, 12:28 PM
    oxford replied to a thread Model A enthusiasts? in General
    I know there are conversion kits to put a t5 transmission into the A’s. My dad picked up the trans for his roadster but that is as far as he got. I...
    11 replies | 829 view(s)
  • oxford's Avatar
    12-18-2018, 10:44 PM
    Curious as to why you want the extra fine thread? I thought for fine tune ability but then you mention hydraulic jacks.
    55 replies | 4212 view(s)
  • oxford's Avatar
    12-11-2018, 08:08 PM
    oxford replied to a thread Glue For Neoprene Rubber in General
    There is also the “yellow” trim adhesive that comes in a squeeze tube. The ones we used to use was in a red tube. On a quick google search it was...
    39 replies | 1852 view(s)
No More Results
About oxford

Basic Information

About oxford
Location:
Northeast, PA

Statistics


Total Posts
Total Posts
1,173
Posts Per Day
0.42
General Information
Last Activity
Today 08:33 PM
Join Date
06-11-2011
Referrals
0