Tab Content
  • larry_g's Avatar
    09-09-2019, 12:10 AM
    One way to get a cyclic load is to have a continuous belt that goes up and over a pulley and then back down to a lower pulley. On the belt, or...
    272 replies | 109775 view(s)
  • larry_g's Avatar
    09-02-2019, 04:57 PM
    Watched some of the harvest on utube and read a bit. Seems you have similar issues that we have with grass seed here in the Willamette Valley. Have...
    23 replies | 1625 view(s)
  • larry_g's Avatar
    09-02-2019, 01:28 AM
    I can remember having something similar on one of the old tractors Grandpa had. What are you cutting this time of the year that is so wet? Swathers...
    23 replies | 1625 view(s)
  • larry_g's Avatar
    08-28-2019, 07:35 PM
    larry_g replied to a thread Heavy duty die holder in General
    Great solution and execution. When I steal your design I think that instead of welding in the handles I will bore a 1/2" hole and then a 3/8" thread...
    16 replies | 1135 view(s)
  • larry_g's Avatar
    08-20-2019, 03:54 PM
    Sliding calipers (vernier, dial, digital)- yes Micrometers- yes Dial gauges- yes Test indicator- yes Sensitive (.0001"/.001mm) test indicator-...
    49 replies | 4134 view(s)
  • larry_g's Avatar
    08-16-2019, 01:35 PM
    On the cylinder part of the timing of the steam inlet is that the intake valve opens a bit before TDC so that the steam pressure assists in stopping...
    19 replies | 1480 view(s)
  • larry_g's Avatar
    08-10-2019, 06:58 PM
    larry_g replied to a thread Two Questions in General
    If memory serves me good the max piston speed is when the rod is tangent to the the circle made by the rod throw on the crank. The position is...
    8 replies | 767 view(s)
  • larry_g's Avatar
    08-02-2019, 07:29 PM
    "case steam engine and deutz tractor having a play" It's kinda sad that grown men can't tell the difference between a Deutz and a John Deere...
    25 replies | 2494 view(s)
  • larry_g's Avatar
    07-31-2019, 12:45 AM
    This was my thought. Common to have water in the bottom of the solvent tank to allow solids to precipitate out. If your worried about rust, where...
    36 replies | 2446 view(s)
  • larry_g's Avatar
    07-26-2019, 08:44 PM
    Two things that I have experienced. 1. The spinners get stuff in them and clog the ports. The ones that I have messed with come apart so they can...
    44 replies | 3092 view(s)
  • larry_g's Avatar
    07-22-2019, 11:16 PM
    Criterion type boring heads can come without a shank. Order the shank desperately; ...
    13 replies | 1147 view(s)
  • larry_g's Avatar
    07-14-2019, 11:39 AM
    Since you have your trailer on hand measure and cut a couple of 2x's to span the width of the trailer inside. Once you have the machine/pallet...
    151 replies | 12050 view(s)
No More Results
About larry_g

Basic Information

About larry_g
Location:
Oregon
Occupation:
retired maintenance tech

Statistics


Total Posts
Total Posts
404
Posts Per Day
0.07
Albums
Total Albums
1
Total Photos
4
General Information
Last Activity
09-17-2019 06:09 PM
Join Date
12-03-2004
Referrals
0