Tab Content
  • 10KPete's Avatar
    Yesterday, 08:42 PM
    10KPete replied to a thread Back to Steam-- in General
    Split those bearing blocks before you finish machining them. Makes fitting to the crank much easier.... Looking great! I've had a double on my...
    97 replies | 6585 view(s)
  • 10KPete's Avatar
    Yesterday, 05:42 PM
    Hey danlb, it's stuck together, it works and it's yours and you did it. Pretty comes when it's needed. And will!! Just think: If it ever comes...
    622 replies | 230294 view(s)
  • 10KPete's Avatar
    09-11-2017, 12:49 AM
    10KPete replied to a thread Back to Steam-- in General
    ;) That's the spirit!! Pete
    97 replies | 6585 view(s)
  • 10KPete's Avatar
    09-10-2017, 05:34 PM
    10KPete replied to a thread Shop Made Tools in General
    Very nice block!! I've a couple of chunks waiting that conversion but for ER32.. Pete
    3052 replies | 10210347 view(s)
  • 10KPete's Avatar
    09-10-2017, 05:23 PM
    10KPete replied to a thread Back to Steam-- in General
    You're buying sticks???!!! I buy one width of roll, 1 1/2". 180, 220, 320 grit. Use files for backers, all sizes 14" to needle. Make shapes from...
    97 replies | 6585 view(s)
  • 10KPete's Avatar
    09-09-2017, 03:59 PM
    10KPete replied to a thread What did I buy? in General
    I'll give you $75!!! Great haul!! I've sent you a Private Message. Pete
    34 replies | 3230 view(s)
  • 10KPete's Avatar
    09-05-2017, 05:44 PM
    10KPete replied to a thread motor woes in General
    I would, if possible, make new washers from a suitable material like phenolic sheet. It's been used in motors since, well, motors, is easy to cut and...
    2 replies | 274 view(s)
  • 10KPete's Avatar
    08-21-2017, 10:02 PM
    Simple revolution counter. You supply the timepiece. Pete
    12 replies | 1285 view(s)
  • 10KPete's Avatar
    07-24-2017, 02:31 AM
    10KPete replied to a thread galvanic reactions in General
    The resistance of carbon fiber is so high that galvanic currents just aren't possible. Pete
    5 replies | 688 view(s)
  • 10KPete's Avatar
    06-28-2017, 06:13 PM
    10KPete replied to a thread Tap Storage Tip in General
    I use a similar product for end mills. Great stuff at the kitchen store!! Pete
    9 replies | 1204 view(s)
  • 10KPete's Avatar
    06-26-2017, 12:29 AM
    10KPete replied to a thread Shop Made Tools in General
    Come on guys, start a new thread with this. This isn't a discussion forum.:) Pete
    3052 replies | 10210347 view(s)
No More Results
About 10KPete

Basic Information

About 10KPete
Location:
Nordland, WA
Interests:
Makin' and Fixin'.
Occupation:
Retired mechanical engineering type guy.

Signature


1973 SB 10K w/ collets, 3 & 4 jaws, face plates, bed turret and other 'stuff'.
BenchMaster vertical mill, 6" RT, cheap vise.
Three drill presses, Two bench grinders, Small polishing motor, Hand tools up the kazoo.
And enough junk that I can never find what I need and always have to make or buy
something else.

Statistics


Total Posts
Total Posts
719
Posts Per Day
0.23
General Information
Last Activity
Yesterday 10:30 PM
Join Date
01-19-2009
Referrals
0