Tab Content
  • J Harp's Avatar
    04-18-2018, 12:31 PM
    Bush Hog it, then get a couple of goats to maintain it!
    47 replies | 2137 view(s)
  • J Harp's Avatar
    04-10-2018, 10:08 PM
    J Harp replied to a thread Live Center Question..... in General
    Since you have precision grinding capability, why not make up a new center with enough stickout to put a driving pulley on it, harden it, drive it...
    60 replies | 2257 view(s)
  • J Harp's Avatar
    04-10-2018, 09:13 AM
    J Harp replied to a thread Lets mix it up a bit. in General
    Computers and cell phones certainly make getting info much easier than spending hours in a library looking up something. They don't make the math...
    32 replies | 1548 view(s)
  • J Harp's Avatar
    04-09-2018, 10:53 PM
    J Harp replied to a thread Lets mix it up a bit. in General
    Thanks Dan, That's the same as what I came up with after thinking about it for a while. If I don't do something like that for a while I will...
    32 replies | 1548 view(s)
  • J Harp's Avatar
    04-09-2018, 08:21 PM
    J Harp replied to a thread Lets mix it up a bit. in General
    Thanks for the replies. I'll be printing some of them after I have a chance to review them. I didn't state the question very well, I shouldn't...
    32 replies | 1548 view(s)
  • J Harp's Avatar
    04-08-2018, 08:50 PM
    J Harp replied to a thread Lets mix it up a bit. in General
    In this sort of thing I suppose metric would be less confusing. Generally I am unfamiliar with metric measurements, I know about what 5 gallons looks...
    32 replies | 1548 view(s)
  • J Harp's Avatar
    04-08-2018, 05:00 PM
    J Harp replied to a thread Lets mix it up a bit. in General
    Keith, I hope your sig line doesn't apply to me. Last week I mentioned the projects I'm into to a fellow I was talking with. As we parted he said, "I...
    32 replies | 1548 view(s)
  • J Harp's Avatar
    04-08-2018, 04:38 PM
    J Harp replied to a thread Lets mix it up a bit. in General
    Thanks for the replies, weighing the water sounds workable. One site I looked at said to mix it to the consistency of mashed potatoes, another said...
    32 replies | 1548 view(s)
  • J Harp's Avatar
    04-08-2018, 02:12 PM
    J Harp started a thread Lets mix it up a bit. in General
    Re some recent discussions of exact measurements and different systems of weights and measures, I have a head-scratcher. A bag of mortar mix has...
    32 replies | 1548 view(s)
  • J Harp's Avatar
    04-01-2018, 08:05 AM
    J Harp replied to a thread Third try to post in General
    The jaws are straight and flat, no serrations or holes, when the gripping surfaces are parallel I'm guessing they are about .030 or .035 apart. Maybe...
    3 replies | 231 view(s)
  • J Harp's Avatar
    04-01-2018, 01:19 AM
    J Harp started a thread Third try to post in General
    Tapatalk acting up, or I forgot how to post. Flea market finds. What is the intended use for these pliars, why the curlique on the end of the...
    3 replies | 231 view(s)
  • J Harp's Avatar
    03-29-2018, 10:28 AM
    My thinking may be fuzzy, but here's how I see it. The tool orientation stays the same, pointing toward you. You stay in the same place, in front of...
    152 replies | 9172 view(s)
  • J Harp's Avatar
    03-29-2018, 08:09 AM
    My two cents says the problem is the insert and the way it's being used. To cut internal threads in the usual setup the point of the insert faces the...
    152 replies | 9172 view(s)
  • J Harp's Avatar
    03-28-2018, 11:42 PM
    Looks to me like all the crests are too wide, the first three appear to be wider than the the rest. could this be the result of using an insert...
    152 replies | 9172 view(s)
  • J Harp's Avatar
    03-25-2018, 07:31 AM
    My guess is that the rolling mill was for rolling silver to the desired thickness for joining parts by silver soldering. Don't know about the...
    37 replies | 2672 view(s)
  • J Harp's Avatar
    03-23-2018, 09:45 PM
    J Harp replied to a thread Firefox in General
    Working fine on Ubuntu, and Linux Mint.
    12 replies | 650 view(s)
  • J Harp's Avatar
    02-08-2018, 10:27 PM
    Make it 32, Brian is a "maker". Anyone who can design and build an engine, then tinker with it until it runs to his satisfaction deserves our respect...
    194 replies | 14576 view(s)
  • J Harp's Avatar
    02-07-2018, 06:49 PM
    I didn't state my previous question very well. What I meant was could the aluminum plug be expanding the stainless cylinder more than it would shrink...
    194 replies | 14576 view(s)
  • J Harp's Avatar
    02-07-2018, 12:42 PM
    Brian, a way back in the thread I believe you said the displacer piston was stainless steel with aluminum end plugs. Could the greater expansion of...
    194 replies | 14576 view(s)
  • J Harp's Avatar
    02-05-2018, 11:32 PM
    Thanks, I don't recall ever seeing one like that before.
    17 replies | 1226 view(s)
  • J Harp's Avatar
    02-05-2018, 09:43 PM
    What is the part between the four-way tool block and the compound on your original setup? Thanks for posting the disassembly how-to.
    17 replies | 1226 view(s)
  • J Harp's Avatar
    02-02-2018, 08:15 PM
    J Harp started a thread Building a bridge! in General
    http://www.trendingly.com/wowjoint Has anyone else done this? If they have I missed it.
    3 replies | 719 view(s)
  • J Harp's Avatar
    01-31-2018, 10:44 PM
    J Harp replied to a thread OT: Kind of a long train in General
    "Quote" Passenger trains toot --- . . --- which is P in Morse code, Not when I learned Morse. I make that dah didi dah which is X. P is di dah dah...
    37 replies | 3193 view(s)
No More Results
About J Harp

Basic Information

About J Harp
Location:
Louisville Ky
Interests:
Wood & metal work, gardening
Occupation:
Retired driver

Signature


Jim

Statistics


Total Posts
Total Posts
675
Posts Per Day
0.14
General Information
Last Activity
Yesterday 11:13 PM
Join Date
04-18-2005
Referrals
0