Tab Content
  • J Harp's Avatar
    05-05-2018, 01:36 PM
    J Harp replied to a thread Extreme edge of Lo-Tech in General
    We---ll that looked easy till I tried to do it. Trying to resize the pictures kept crashing my laptop. Switched to the desktop and kept after it till...
    14 replies | 1411 view(s)
  • J Harp's Avatar
    05-05-2018, 01:03 PM
    J Harp added 2 photo(s) to album J Harp's Pictures
  • J Harp's Avatar
    05-05-2018, 12:56 PM
    J Harp created an album J Harp's Pictures
  • J Harp's Avatar
    05-04-2018, 10:52 PM
    J Harp replied to a thread Extreme edge of Lo-Tech in General
    I also made a low tech chip rake yesterday, but can't figure out how to insert a picture in a reply with tapatalk. I've printed George's instructions...
    14 replies | 1411 view(s)
  • J Harp's Avatar
    05-03-2018, 09:04 PM
    Ames shovels, I think they were being made before the American Revolution.
    24 replies | 2238 view(s)
  • J Harp's Avatar
    04-25-2018, 08:04 PM
    J Harp replied to a thread Tool Time, What is it? in General
    Something makes me think it's a bung tool form use on steel drums, or other containers that might hold flammable liquids. Those "horns" behind the...
    14 replies | 1596 view(s)
  • J Harp's Avatar
    04-18-2018, 12:31 PM
    Bush Hog it, then get a couple of goats to maintain it!
    47 replies | 3078 view(s)
  • J Harp's Avatar
    04-10-2018, 10:08 PM
    J Harp replied to a thread Live Center Question..... in General
    Since you have precision grinding capability, why not make up a new center with enough stickout to put a driving pulley on it, harden it, drive it...
    60 replies | 4353 view(s)
  • J Harp's Avatar
    04-10-2018, 09:13 AM
    J Harp replied to a thread Lets mix it up a bit. in General
    Computers and cell phones certainly make getting info much easier than spending hours in a library looking up something. They don't make the math...
    32 replies | 2429 view(s)
  • J Harp's Avatar
    04-09-2018, 10:53 PM
    J Harp replied to a thread Lets mix it up a bit. in General
    Thanks Dan, That's the same as what I came up with after thinking about it for a while. If I don't do something like that for a while I will...
    32 replies | 2429 view(s)
  • J Harp's Avatar
    04-09-2018, 08:21 PM
    J Harp replied to a thread Lets mix it up a bit. in General
    Thanks for the replies. I'll be printing some of them after I have a chance to review them. I didn't state the question very well, I shouldn't...
    32 replies | 2429 view(s)
  • J Harp's Avatar
    04-08-2018, 08:50 PM
    J Harp replied to a thread Lets mix it up a bit. in General
    In this sort of thing I suppose metric would be less confusing. Generally I am unfamiliar with metric measurements, I know about what 5 gallons looks...
    32 replies | 2429 view(s)
  • J Harp's Avatar
    04-08-2018, 05:00 PM
    J Harp replied to a thread Lets mix it up a bit. in General
    Keith, I hope your sig line doesn't apply to me. Last week I mentioned the projects I'm into to a fellow I was talking with. As we parted he said, "I...
    32 replies | 2429 view(s)
  • J Harp's Avatar
    04-08-2018, 04:38 PM
    J Harp replied to a thread Lets mix it up a bit. in General
    Thanks for the replies, weighing the water sounds workable. One site I looked at said to mix it to the consistency of mashed potatoes, another said...
    32 replies | 2429 view(s)
  • J Harp's Avatar
    04-08-2018, 02:12 PM
    J Harp started a thread Lets mix it up a bit. in General
    Re some recent discussions of exact measurements and different systems of weights and measures, I have a head-scratcher. A bag of mortar mix has...
    32 replies | 2429 view(s)
  • J Harp's Avatar
    04-01-2018, 08:05 AM
    J Harp replied to a thread Third try to post in General
    The jaws are straight and flat, no serrations or holes, when the gripping surfaces are parallel I'm guessing they are about .030 or .035 apart. Maybe...
    3 replies | 335 view(s)
  • J Harp's Avatar
    04-01-2018, 01:19 AM
    J Harp started a thread Third try to post in General
    Tapatalk acting up, or I forgot how to post. Flea market finds. What is the intended use for these pliars, why the curlique on the end of the...
    3 replies | 335 view(s)
  • J Harp's Avatar
    03-29-2018, 10:28 AM
    My thinking may be fuzzy, but here's how I see it. The tool orientation stays the same, pointing toward you. You stay in the same place, in front of...
    229 replies | 15428 view(s)
  • J Harp's Avatar
    03-29-2018, 08:09 AM
    My two cents says the problem is the insert and the way it's being used. To cut internal threads in the usual setup the point of the insert faces the...
    229 replies | 15428 view(s)
  • J Harp's Avatar
    03-28-2018, 11:42 PM
    Looks to me like all the crests are too wide, the first three appear to be wider than the the rest. could this be the result of using an insert...
    229 replies | 15428 view(s)
  • J Harp's Avatar
    03-25-2018, 07:31 AM
    My guess is that the rolling mill was for rolling silver to the desired thickness for joining parts by silver soldering. Don't know about the...
    37 replies | 3206 view(s)
No More Results
About J Harp

Basic Information

About J Harp
Location:
Louisville Ky
Interests:
Wood & metal work, gardening
Occupation:
Retired driver

Signature


Jim

Statistics


Total Posts
Total Posts
679
Posts Per Day
0.14
Albums
Total Albums
1
Total Photos
2
General Information
Last Activity
Yesterday 08:44 PM
Join Date
04-18-2005
Referrals
0