Tab Content
  • TGTool's Avatar
    Yesterday, 09:38 PM
    Back in the early 70's I was working on the exhaust system for a car in the shop, Mercedes if I remember. Up on the hoist I'm looking at the bell...
    26 replies | 770 view(s)
  • TGTool's Avatar
    Yesterday, 09:22 PM
    TGTool replied to a thread I made a Repeat O Meter in General
    All very nicely done, well thought out and well explained.
    18 replies | 962 view(s)
  • TGTool's Avatar
    Yesterday, 10:15 AM
    TGTool replied to a thread I made a Repeat O Meter in General
    The front piece needs to be able to move up and down at the end where the indicator is. That is, it's essentially tracking just the one foot at the...
    18 replies | 962 view(s)
  • TGTool's Avatar
    09-11-2019, 09:56 PM
    It gets only occasional use for a variety of reasons. One, I don't have enough room in the shop so if I want to use it I have to do some shifting...
    40 replies | 2774 view(s)
  • TGTool's Avatar
    09-11-2019, 02:37 PM
    I've also built one. There's a Yahoo group devoted to the Quorn and some work-alikes. The files and photos sections have a lot of pictures of...
    40 replies | 2774 view(s)
  • TGTool's Avatar
    09-10-2019, 09:15 AM
    Boy, that raises a question I never thought to worry about. I've got a Quorn and the screw and dial are graduated in thousanths of an inch. I've...
    40 replies | 2774 view(s)
  • TGTool's Avatar
    09-06-2019, 10:22 AM
    TGTool replied to a thread Bench Grinder Mod Question in General
    I'm not giving you a hard time. We need to pay constant attention to safety issues, but realistically some situations are impossible or impractical...
    30 replies | 1717 view(s)
  • TGTool's Avatar
    09-05-2019, 03:50 PM
    TGTool replied to a thread Bench Grinder Mod Question in General
    Do you have a pic of how you installed the wheel guards afterwards? :D I guess if the lathe is big enough to swing the guards too ....
    30 replies | 1717 view(s)
  • TGTool's Avatar
    09-05-2019, 10:37 AM
    TGTool replied to a thread Bench Grinder Mod Question in General
    On a similar grinder I just made up thicker washers for the inner side that were a close fit on the shaft. I don't have them here in front of me,...
    30 replies | 1717 view(s)
  • TGTool's Avatar
    08-20-2019, 11:42 PM
    TGTool replied to a thread O.T. Fluke Meter Leads. in General
    I recently got a set of leads at Lowes with crocodile's. I can't remember what I paid but less than $40 I'm pretty sure. Banana plugs fit the other...
    33 replies | 2509 view(s)
  • TGTool's Avatar
    08-14-2019, 12:21 PM
    TGTool replied to a thread Dog bite story---O.T. in General
    Yeah, that's entirely likely. But it's really foisting their own problem off on others. So, would they accept this scenario? I've got a dog...
    32 replies | 2254 view(s)
  • TGTool's Avatar
    08-14-2019, 11:36 AM
    TGTool replied to a thread Dog bite story---O.T. in General
    Bet they won't buy me the electric mower so we can all have more peace, though.
    32 replies | 2254 view(s)
  • TGTool's Avatar
    08-13-2019, 06:15 PM
    TGTool replied to a thread Dog bite story---O.T. in General
    This isn't a serious problem but it is annoying. I'm currently living in a house with a fenced in back yard. All the neighbor yards are also wood...
    32 replies | 2254 view(s)
  • TGTool's Avatar
    07-29-2019, 08:20 PM
    TGTool replied to a thread Run-away Engine--sorta o.t. in General
    I heard a story passed on about an old mechanic in Des Moines when I was in college. He was legendary for working on import cars and was reputed to...
    9 replies | 1190 view(s)
No More Results
About TGTool

Basic Information

Date of Birth
November 30

Signature


.
"People will occasionally stumble over the truth, but most of the time they will pick themselves up and carry on" : Winston Churchill

Statistics


Total Posts
Total Posts
3,395
Posts Per Day
0.66
Albums
Total Albums
1
Total Photos
10
General Information
Last Activity
Today 09:04 AM
Join Date
08-18-2005
Referrals
0