Tab Content
  • duckman's Avatar
    03-14-2018, 07:12 PM
    The best thing I did with my SB (52" Kubota) is install an electric motor on the chute rotator it was 38 turns from left to right, looking in the...
    50 replies | 4538 view(s)
  • duckman's Avatar
    03-13-2018, 01:08 PM
    duckman replied to a thread Just wondering: in General
    They are behind because they're waiting for the chinese shipment to come in , oh sorry I mean the globally sourced products.
    6 replies | 440 view(s)
  • duckman's Avatar
    03-11-2018, 07:40 PM
    duckman replied to a thread Import Steel Quality in General
    The comp. that I work for uses a lot of 4120 & 4140 the crap we're getting now is horrible to turn, reputable co. we get it from but on the ends of...
    33 replies | 1754 view(s)
  • duckman's Avatar
    02-17-2018, 09:01 PM
    But you need to remember if you tighten the set screw to much you make the end of the quill egg shaped and it still won't go up until you jam it,...
    24 replies | 2038 view(s)
  • duckman's Avatar
    02-17-2018, 08:51 PM
    First make sure your pin is round put it in a vee block and rotate it while checking with a very fussy indicator, while it can be measured with a...
    13 replies | 980 view(s)
  • duckman's Avatar
    02-04-2018, 05:58 PM
    We had some at a place that I worked, but the monkeys kept breaking the cable that runs inside and they were Starretts.
    15 replies | 1064 view(s)
  • duckman's Avatar
    02-04-2018, 05:33 PM
    It really feels strange when they are not there, rumor has it there plane is at the painters getting ready to put on the 6th Lombardi trophy on the...
    33 replies | 1604 view(s)
  • duckman's Avatar
    01-31-2018, 08:23 PM
    Just remember magnets and steel don't mix but they do stick, I've got glass scales on my BRPT going on 7 years (from CDCO) never had a problem . I...
    20 replies | 1621 view(s)
  • duckman's Avatar
    01-25-2018, 04:48 PM
    Just had a Noga adjuster apart at work no springs they use belleville washers, ingenious use, the fine adjuster might use the same thing look for a...
    29 replies | 1809 view(s)
  • duckman's Avatar
    01-24-2018, 05:39 PM
    Had to mill a 1/2" key way with weird depth .445" oh ya its 18" long in PHT 4140.
    993 replies | 329728 view(s)
  • duckman's Avatar
    01-23-2018, 04:22 PM
    duckman replied to a thread Carbon Monoxide Dectors in General
    I was under the impression that CO is a heavy gas/fume so why mount them in the ceiling , I was told mount them low so they can react b4 you die.
    19 replies | 984 view(s)
  • duckman's Avatar
    01-10-2018, 06:23 PM
    duckman started a thread Cabin Fever in General
    There will be some good stuff at the CFE flea market I will be bringing a set of Starrett 0"-12" mikes in factory box, and a Dapra flacker, time to...
    8 replies | 929 view(s)
  • duckman's Avatar
    01-06-2018, 11:39 AM
    My turn to to throw some gas on the fire , real chili DOES NOT have meat , it was invented during the cattle drives when there was no refrigeration...
    242 replies | 11770 view(s)
  • duckman's Avatar
    01-04-2018, 07:06 PM
    duckman replied to a thread OT: Snow Comming in General
    I'm in north central Mass. we were supposed to get 3/7" HA HA got home from work with 10"+ on the ground got the tractor started with the new 52"...
    19 replies | 1427 view(s)
  • duckman's Avatar
    12-28-2017, 07:09 PM
    duckman replied to a thread Shop Lights Are Done in General
    Here in the North East we have a store called Ocean State Job Lot they have 48" LED light's for $15.00 ea, 4,000 lumen, 5,000 kelvin and 48 watt I...
    14 replies | 1145 view(s)
No More Results
About duckman

Basic Information

About duckman
Winchendon MA
building stuff
employed again


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Yesterday 10:22 PM
Join Date