• outlawspeeder's Avatar
    07-03-2017, 10:04 AM
    outlawspeeder replied to a thread New Shop equipment suggestions? in General
    Plan the 6X6 but I found that you should plan to expand. There is this bug that bites you and it gets out of control. My suggestion: site down...
    see more
    23 replies | 1777 view(s)
  • outlawspeeder's Avatar
    06-16-2017, 11:50 PM
    outlawspeeder replied to a thread Help with compressor motor problem in General
    One more thought: 40 years I would say the motor is worn out. Take the side load off the motor and check to see if the motor shaft is grounding out...
    see more
    17 replies | 1073 view(s)
  • outlawspeeder's Avatar
    06-16-2017, 03:11 PM
    outlawspeeder replied to a thread Powering a motor in General
    So has anyone build and put this to use? This looks like what I am looking for. The motor maxed out at 130 Volt. This would be 120max meaning I...
    see more
    30 replies | 1822 view(s)
  • outlawspeeder's Avatar
    06-15-2017, 06:00 PM
    outlawspeeder replied to a thread Powering a motor in General
    The one diode. I never thought of that. Half the sine wave.
    see more
    30 replies | 1822 view(s)
  • outlawspeeder's Avatar
    06-15-2017, 05:07 PM
    outlawspeeder replied to a thread Powering a motor in General
    And that my friends is call crowed sourcing. In the last 45 minute I went from knowing just enough to burn up the motor to knowing where to start...
    see more
    30 replies | 1822 view(s)
  • outlawspeeder's Avatar
    06-15-2017, 04:30 PM
    outlawspeeder replied to a thread Powering a motor in General
    States 120. Thank you, that's a starting point.
    see more
    30 replies | 1822 view(s)
  • outlawspeeder's Avatar
    06-15-2017, 04:15 PM
    outlawspeeder started a thread Powering a motor in General
    Ok I need someone smarter than me. That's everyone on this site. I got a free geared motor that I need to power for a project. Label reads:...
    see more
    30 replies | 1822 view(s)
  • outlawspeeder's Avatar
    05-23-2017, 05:53 PM
    outlawspeeder replied to a thread Joining a band saw blade in General
    I have a blade welder and live in the St Louis area if it helps. Be cheap I'll keep old blades and reuse good parts of bad blades.
    see more
    13 replies | 1242 view(s)
  • outlawspeeder's Avatar
    05-23-2017, 04:28 PM
    outlawspeeder started a thread Boston Gear 700 with a stuck motor. in General
    I was scrounging this last weekend and came across a Boston Gear 700 with a 3 phase motor. (20US dollars) It was vent side down so I figure I would...
    see more
    2 replies | 486 view(s)
  • outlawspeeder's Avatar
    04-30-2017, 11:05 PM
    outlawspeeder replied to a thread Making a bolt slot hole. in General
    I played with making a punch and die today. I found that I need a piece of harder steel than what I had today(Sunday). With failure comes a lesson....
    see more
    22 replies | 2664 view(s)
  • outlawspeeder's Avatar
    04-29-2017, 09:26 PM
    outlawspeeder replied to a thread Making a bolt slot hole. in General
    Its looking like the mill is the way to go. Punch and die is 140, and I would still have to build the parts to keep it right on the press.
    see more
    22 replies | 2664 view(s)
  • outlawspeeder's Avatar
    04-29-2017, 08:22 PM
    outlawspeeder started a thread Making a bolt slot hole. in General
    I have some hot rolled 1/8 steel I need to put some bolt slots in. I need the hole 1/4 by 1/2. This will allow the bolt to slide right and left. I...
    see more
    22 replies | 2664 view(s)
No More Results
About outlawspeeder

Basic Information

Statistics


Total Posts
Total Posts
457
Posts Per Day
0.26
General Information
Last Activity
Today 12:06 AM
Join Date
10-10-2012
Referrals
0