Tab Content
  • olf20's Avatar
    09-13-2017, 01:25 PM
    olf20 replied to a thread Band Saw Riser Block in General
    I have a bunch of walnut that my late brother gave me. I started making wooden spoons and bowls. The length of the wood is about two feet long. I...
    28 replies | 1548 view(s)
  • olf20's Avatar
    09-12-2017, 07:18 PM
    olf20 replied to a thread Band Saw Riser Block in General
    Yea I saw the Grizzly riser blocks. I'm going to take a few measurements on my saw, and see if the Grizzly block will work. Should save lots of...
    28 replies | 1548 view(s)
  • olf20's Avatar
    09-10-2017, 11:17 PM
    olf20 replied to a thread Band Saw Riser Block in General
    Thanks Beazld, that would help! You gona get any storm where you live? olf20 / Bob
    28 replies | 1548 view(s)
  • olf20's Avatar
    09-10-2017, 09:41 PM
    olf20 replied to a thread Band Saw Riser Block in General
    Thanks for the replies! I just went on Ebay and man they want $160 to $220 for the riser block kits. I'm sure I can make something for that price....
    28 replies | 1548 view(s)
  • olf20's Avatar
    09-10-2017, 07:09 PM
    olf20 started a thread Band Saw Riser Block in General
    I have a generic band saw and want to put a riser block in it to increase it's capacity. I think it is a delta knock off. Have you made your own...
    28 replies | 1548 view(s)
  • olf20's Avatar
    08-31-2017, 07:47 AM
    olf20 replied to a thread Digital Read Out w Encoder in General
    Got a reply back from supplier and they said the display that I posted will not accept a rotary encoder. O well on the something else. Thanks for...
    17 replies | 885 view(s)
  • olf20's Avatar
    08-30-2017, 11:07 PM
    olf20 replied to a thread Digital Read Out w Encoder in General
    So that's why glass scales are the preferred method. I just did not want to mount them on the mill. Maybe I'll have to relook at that. olf20 / Bob
    17 replies | 885 view(s)
  • olf20's Avatar
    08-30-2017, 09:37 PM
    olf20 replied to a thread Digital Read Out w Encoder in General
    The stepper motor shaft results in .200 per revaluation. This is one of the several encoders that this supplier offers....
    17 replies | 885 view(s)
  • olf20's Avatar
    08-30-2017, 05:55 PM
    olf20 replied to a thread Digital Read Out w Encoder in General
    My steppers are dual shaft. I was going to mount them to the shaft. olf20 / Bob
    17 replies | 885 view(s)
  • olf20's Avatar
    08-30-2017, 05:16 PM
    olf20 replied to a thread Digital Read Out w Encoder in General
    I don't have a reply from the supplier yet, but here is a link with a diagram of different inputs....
    17 replies | 885 view(s)
  • olf20's Avatar
    08-30-2017, 03:59 PM
    olf20 replied to a thread Digital Read Out w Encoder in General
    Thanks for the reply. How do I know which encoder to purchase? Here is one display I was looking at on Ebay. They have two axis displays with all...
    17 replies | 885 view(s)
  • olf20's Avatar
    08-30-2017, 03:34 PM
    Do most - some - all digital readouts accept rotary encoder input? I know there are several different encoders out puts. Which ones? Or what do I...
    17 replies | 885 view(s)
  • olf20's Avatar
    08-27-2017, 07:40 PM
    If it is the vac u jet, it has a diaphragm on the side which pumps fuel to a small bowl in the top of the tank. Have replaced lots of the...
    11 replies | 902 view(s)
  • olf20's Avatar
    07-27-2017, 07:55 PM
    Thanks, that's what I was looking for. olf20 / Bob
    2 replies | 278 view(s)
  • olf20's Avatar
    07-27-2017, 06:38 PM
    The Z axis on my Bridgeport clone can be rotated a few degrees back and forth. I'm just wondering what holds this in place? Everything works...
    2 replies | 278 view(s)
  • olf20's Avatar
    07-14-2017, 06:34 AM
    Thanks for the replies. The mill will run 12 hours + when cutting a lithophane. I think I will just make it do a full stroke every hour of actual...
    7 replies | 628 view(s)
  • olf20's Avatar
    07-13-2017, 07:39 PM
    Does it take a full stroke to provide full lubrication. I'm making a motor with a eccentric to lube the Mill while it is running long jobs...
    7 replies | 628 view(s)
  • olf20's Avatar
    07-01-2017, 07:04 AM
    I have monkeyed with propane for many years. I have to pump water from a creek to water my cattle. I have used U S Carbruation adapter to power a...
    370 replies | 43423 view(s)
No More Results
About olf20

Basic Information

Statistics


Total Posts
Total Posts
55
Posts Per Day
0.03
General Information
Last Activity
Yesterday 06:53 PM
Join Date
11-17-2012
Referrals
0