Tab Content
  • olf20's Avatar
    01-12-2019, 08:55 PM
    What is your favorite drive? olf20 / Bob
    2 replies | 154 view(s)
  • olf20's Avatar
    01-11-2019, 07:51 AM
    Thanks guys! Could not get link to work. olf20 / Bob
    5 replies | 219 view(s)
  • olf20's Avatar
    01-10-2019, 03:13 PM
    I have a older Lincoln stick welder. It quit working and tore it apart and found the contacts pitted and rough. Cleaned everything up and tested...
    5 replies | 219 view(s)
  • olf20's Avatar
    12-29-2018, 07:51 PM
    olf20 replied to a thread Back to Turning a Barrel in General
    Use house trim material from menards. Easy to cut and bend. Strong! Lots of scrap laying around. olf20 / Bob
    13 replies | 737 view(s)
  • olf20's Avatar
    12-25-2018, 08:12 AM
    Merry Christmas to all from NW Illinois. Thanks Brian for sharing your work. I'm a hobby guy and have learned so much from you and the people...
    16 replies | 603 view(s)
  • olf20's Avatar
    12-21-2018, 08:25 AM
    olf20 replied to a thread Rotary phase converter motor in General
    I'm a real rookie compared to you guys. But I built one 10 years ago. Went to local machine shop, asked it they had a xxhp motor that had a bad...
    122 replies | 4944 view(s)
  • olf20's Avatar
    12-06-2018, 08:14 AM
    olf20 replied to a thread CNC Mill False Stops in General
    This happens fairly infrequent. I will start by doing that while I ponder other suggestions from this thread. Thanks olf20 / Bob
    34 replies | 1124 view(s)
  • olf20's Avatar
    12-05-2018, 08:23 AM
    olf20 replied to a thread CNC Mill False Stops in General
    I'm sure my cabinet has room for improvement as I'm not a electrical anything. However I have done many projects in my life with great success. I'm...
    34 replies | 1124 view(s)
  • olf20's Avatar
    12-04-2018, 09:56 PM
    olf20 replied to a thread CNC Mill False Stops in General
    Yea I've played with the debounce, I'm at 1000 now. The settings are now in the ESS setup. Follow this link:...
    34 replies | 1124 view(s)
  • olf20's Avatar
    12-04-2018, 09:39 PM
    olf20 replied to a thread CNC Mill False Stops in General
    These are all separate 5vdc logic. Each switch has its own input. All limit switches are NC, as with the Estop and Feedhold. olf20 / Bob
    34 replies | 1124 view(s)
  • olf20's Avatar
    12-04-2018, 09:35 PM
    olf20 replied to a thread CNC Mill False Stops in General
    Found a ground loop several months ago. Fixed that but still have the occasional stop. Did not earth ground any. olf20 / Bob
    34 replies | 1124 view(s)
  • olf20's Avatar
    12-04-2018, 09:18 AM
    olf20 replied to a thread CNC Mill False Stops in General
    I know several hard core Mach3 guys have went with the 24V. Would consider. What I'm after is to be able to identify which input caused the...
    34 replies | 1124 view(s)
  • olf20's Avatar
    12-03-2018, 09:34 PM
    olf20 replied to a thread CNC Mill False Stops in General
    Thanks for the reply Bob! Yes it shows the stop, but no input details. With 4 limit / home switches, feed hold, and estop one never really knows...
    34 replies | 1124 view(s)
  • olf20's Avatar
    12-03-2018, 07:23 PM
    olf20 started a thread CNC Mill False Stops in General
    I have a hobby cnc mill. I rarely have a problem with it but when I do I never know what caused the problem. Forever I have wanted to put something...
    34 replies | 1124 view(s)
  • olf20's Avatar
    11-13-2018, 08:18 AM
    Put a small watt led bulb in. Works great!! Great! olf20 / Bob
    24 replies | 997 view(s)
  • olf20's Avatar
    11-12-2018, 08:46 AM
    Thanks for the replies! I have another camera monitoring the main floor that I can see the room temperature. The small light bulb is what I'll...
    24 replies | 997 view(s)
  • olf20's Avatar
    11-11-2018, 05:59 PM
    I have a hot water heat system in our house. I recently installed a home security camera system. I installed one in the boiler room with a...
    24 replies | 997 view(s)
  • olf20's Avatar
    10-26-2018, 08:08 AM
    Thanks! olf20 / Bob
    1 replies | 278 view(s)
No More Results
About olf20

Basic Information

Statistics


Total Posts
Total Posts
102
Posts Per Day
0.05
Albums
Total Albums
1
Total Photos
0
General Information
Last Activity
Today 07:20 AM
Join Date
11-17-2012
Referrals
0