Tab Content
  • jmm03's Avatar
    09-13-2018, 03:35 PM
    and they laughed at me because I wear a tinfoil hat... Don't most cars in the last 5 or so years have an onboard "black box" that retrievable...
    14 replies | 707 view(s)
  • jmm03's Avatar
    09-07-2018, 04:04 PM
    jmm03 replied to a thread Shop Made Tools in General
    Matt, are the plates countersunk enough that the ball bears on them and not the magnet? Jim
    3387 replies | 11353078 view(s)
  • jmm03's Avatar
    09-06-2018, 12:52 PM
    jmm03 replied to a thread who MAKES the best files in General
    I second mars-red on the NOS and old Nicholsons and Grobet. I know I have files that are 30 plus years old and I use them alot. Jim
    24 replies | 1909 view(s)
  • jmm03's Avatar
    08-29-2018, 03:25 PM
    jmm03 replied to a thread Speaking of Screwdrivers... in General
    probably chinese torx, or chorx as it is known. does not fit any known driver, sae or metric, and if you do manage to jam something in there it...
    25 replies | 1406 view(s)
  • jmm03's Avatar
    08-22-2018, 05:26 PM
    jmm03 replied to a thread Welding plactics in General
    Mike, as far as I know they still sell the model I referenced. If you do get that one buy the warranty. (and always turn the rheostat down and let it...
    21 replies | 1208 view(s)
  • jmm03's Avatar
    08-22-2018, 03:20 PM
    jmm03 replied to a thread Welding plactics in General
    what kind of plastic Mike? We do a fair amount of fabrication on polypropylene equipment like tanks, mounts ,covers etc. I use a horrible freight...
    21 replies | 1208 view(s)
  • jmm03's Avatar
    08-10-2018, 12:59 PM
    On one of our paint booths we don't have a reefer air dryer. It is supplied by an old IR recip unit, maybe a 5 hp. The filter assembly however is the...
    30 replies | 1489 view(s)
  • jmm03's Avatar
    08-09-2018, 08:37 PM
    jmm03 replied to a thread Hi all in General
    only if you have the wrong syrup...
    44 replies | 2068 view(s)
  • jmm03's Avatar
    08-08-2018, 03:42 PM
    Doc, we are in southern california, very low humidity. The housings we use are approximately 10 lb. housings. We use the paint booths all day...
    30 replies | 1489 view(s)
  • jmm03's Avatar
    08-08-2018, 11:08 AM
    Bruce, was the dryer you used a chamber type or what? The ones we use all you do is open up the top and bottom,the old desiccant beads drain out, and...
    30 replies | 1489 view(s)
  • jmm03's Avatar
    08-08-2018, 08:12 AM
    Hi Doc, we have 5 paint booths at work that we use a combo of coalescent and bulk desiccant filters on . We buy bulk desiccant from these guys:...
    30 replies | 1489 view(s)
  • jmm03's Avatar
    07-23-2018, 03:52 PM
    how many holes do you tolerate in your socks before you throw them out, (or recycle them)? Jim
    40 replies | 1924 view(s)
  • jmm03's Avatar
    07-13-2018, 08:22 PM
    Painting is an approved method of coating PVC gas vent pipe so it would probably last for awhile. I agree with the nastiness of cutting plastics and...
    23 replies | 920 view(s)
  • jmm03's Avatar
    07-13-2018, 04:23 PM
    On cutting any of the composite/ fiberglass materials buy yourself a diamond blade, I went through I don't remember how many carbide tipped blades...
    23 replies | 920 view(s)
  • jmm03's Avatar
    07-11-2018, 12:01 PM
    jmm03 replied to a thread relief grind on parting tool in General
    Sorry, the relief I was talking about is clearance on the leading edge (the cutting edge) The tool I am using is brand new, it has clearance under...
    18 replies | 1034 view(s)
  • jmm03's Avatar
    07-11-2018, 08:11 AM
    Hello all, should a new HSS parting tool be ground before use? It already has back relief but it appears to be flat across the cutting edge. Thanks,...
    18 replies | 1034 view(s)
  • jmm03's Avatar
    07-07-2018, 10:52 PM
    jmm03 replied to a thread look at this in General
    Hi Brett, thanks for the link, all machining, no bloviating... Jim
    45 replies | 5100 view(s)
  • jmm03's Avatar
    06-29-2018, 03:54 PM
    jmm03 replied to a thread Cannon help in General
    It would probably be safe to assume that if it had a charge in it, it still does. Otherwise it would have burst the bore if it had been fired, and if...
    87 replies | 7184 view(s)
No More Results
About jmm03

Basic Information

About jmm03
Location:
Ventura,CA.

Statistics


Total Posts
Total Posts
106
Posts Per Day
0.06
General Information
Last Activity
Today 11:32 AM
Join Date
04-02-2014
Referrals
0