Tab Content
  • jmm03's Avatar
    11-08-2018, 09:05 AM
    Thanks to all so far, I suspected there was not a significant difference among the various off brand suppliers, but a reference from those that...
    24 replies | 1397 view(s)
  • jmm03's Avatar
    11-08-2018, 12:46 AM
    chungoo forge=any generic offshore brand...
    24 replies | 1397 view(s)
  • jmm03's Avatar
    11-07-2018, 09:22 PM
    Hello all, we have a lathe at work that came with a chungoo forge wedge type tool holder. Its not a Dorian but it is perfectly functional for our...
    24 replies | 1397 view(s)
  • jmm03's Avatar
    10-25-2018, 04:30 PM
    jmm03 replied to a thread Where do I start? in General
    bring a prybar,some 2x4 and small plywood blocks, 4 pieces of 3/4" rigid conduit or pipe,a friend, and egyptian roll it, if all you can get is a tilt...
    80 replies | 5128 view(s)
  • jmm03's Avatar
    10-23-2018, 09:09 AM
    Do you weld? If so, weld a piece of 4" flat bar along the length of one side to close the gap and fab up a latch that attaches to the other side with...
    15 replies | 999 view(s)
  • jmm03's Avatar
    10-21-2018, 07:12 PM
    jmm03 replied to a thread Machine Moving Question I in General
    Crane trucks are pretty common here but typically there is a 4 hour minimum and it can be prohibitively expensive. You would think that there would...
    23 replies | 1515 view(s)
  • jmm03's Avatar
    10-21-2018, 04:33 PM
    jmm03 replied to a thread Machine Moving Question I in General
    good advise above, mainly from Mcgyver. If the shaper has a completely flat bottom I would forgo the skates and use some 1 1/2" pipe just big enough...
    23 replies | 1515 view(s)
  • jmm03's Avatar
    10-20-2018, 01:02 PM
    jmm03 replied to a thread Where do I start? in General
    while I agree with Boslab on his recommendations, I believe a slight modification might be more useful. Please don't get me wrong, I am no proponent...
    80 replies | 5128 view(s)
  • jmm03's Avatar
    10-19-2018, 09:48 PM
    jmm03 replied to a thread Where do I start? in General
    Hi Cap, you mentioned that you like shooting. Take some gunsmithing classes . Or enroll in those machining courses you talked about, you could make...
    80 replies | 5128 view(s)
  • jmm03's Avatar
    10-15-2018, 04:20 PM
    jmm03 replied to a thread BandSaw Question in General
    I put a 1 hp DC motor and motor controller on my Delta 14", I cut everything without a problem. The old W&T's are great saws, parts can be a...
    35 replies | 2572 view(s)
  • jmm03's Avatar
    10-01-2018, 07:07 PM
    Does one have to get permission to use the right of way, or do you only go on retired/abandoned track? Jim
    17 replies | 1604 view(s)
  • jmm03's Avatar
    09-13-2018, 04:35 PM
    and they laughed at me because I wear a tinfoil hat... Don't most cars in the last 5 or so years have an onboard "black box" that retrievable...
    14 replies | 1138 view(s)
No More Results
About jmm03

Basic Information

About jmm03
Location:
Ventura,CA.

Statistics


Total Posts
Total Posts
117
Posts Per Day
0.07
General Information
Last Activity
Today 01:37 PM
Join Date
04-02-2014
Referrals
0