Search:

Type: Posts; User: elf

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    17
    Views
    583

    Will Kicad or Fritzing do what you need?

    Will Kicad or Fritzing do what you need?
  2. Thread: Swivel eye?

    by elf
    Replies
    32
    Views
    1,170

    It would be rather hard to rotate the lathe...

    It would be rather hard to rotate the lathe relative to its base with a pinch bar :rolleyes:
  3. It seems it did end poorly for the warship in...

    It seems it did end poorly for the warship in this case :p
  4. There is nothing in the rules granting exceptions...

    There is nothing in the rules granting exceptions to vessels engaged in wartime activity, let alone even being a warship.
  5. Why does it need to be a right triangle? Measure...

    Why does it need to be a right triangle? Measure the two legs and the hypotenuse and plug the numbers into a CAD program. For extra credit, calculate what angle each course needs to be cut at in...
  6. Replies
    31
    Views
    2,155

    It's been ten years since @jackary posted his...

    It's been ten years since @jackary posted his modern implementation of the MetalMaster and called it the Stepperhead.
  7. Replies
    31
    Views
    2,155

    Looks a lot like an Urwick MetalMaster...

    Looks a lot like an Urwick MetalMaster.
  8. Replies
    20
    Views
    806

    MDF. It's porous enough that you don't need...

    MDF. It's porous enough that you don't need grooves.
  9. Replies
    11
    Views
    754

    Spot heating may work as well if not better than...

    Spot heating may work as well if not better than pressing on the high spot.
  10. Replies
    298
    Views
    378,013

    Did you make an EvaNut or a cast epoxy nut?

    Did you make an EvaNut or a cast epoxy nut?
  11. Replies
    27
    Views
    1,138

    Self leveling epoxy is often used in situations...

    Self leveling epoxy is often used in situations like this.
  12. Replies
    13
    Views
    545

    Make one using a lathe for the tooth form and...

    Make one using a lathe for the tooth form and mill to remove top half. Heat treat, lap to final size.
  13. Thread: po pholk splines

    by elf
    Replies
    18
    Views
    1,074

    Didn't happen without pictures :D

    Didn't happen without pictures :D
  14. Replies
    3
    Views
    383

    Use hot melt glue or super glue to attach the...

    Use hot melt glue or super glue to attach the blank to a jig. Heat to remove hot melt glue, acetone to remove super glue.
  15. Replies
    170
    Views
    10,116

    21 "new posts" today, only 7 are not machining (...

    21 "new posts" today, only 7 are not machining ( I'm including "Professional - Imports Not Included" and "What did you do today" and this thread in the non-machining category).
  16. Thread: Polishing plastics

    by elf
    Replies
    11
    Views
    511

    It would polish each of those, but it also may...

    It would polish each of those, but it also may remove any coatings.
  17. Based on the thread title, I was going to...

    Based on the thread title, I was going to recommend a shovel.;)
  18. Replies
    8
    Views
    524

    Worth a fortune if you have one of these...

    Worth a fortune if you have one of these.
  19. Replies
    14
    Views
    671

    An HVLP spray gun and a little practice would be...

    An HVLP spray gun and a little practice would be less expensive than a new door.
  20. Tying shoe laces is old school. Try something...

    Tying shoe laces is old school. Try something new.
  21. Replies
    15
    Views
    898

    Start with one of these...

    Start with one of these.
  22. Replies
    63
    Views
    7,372

    I think the OP should just order a $2 item and...

    I think the OP should just order a $2 item and see if they ship it.
  23. Replies
    74
    Views
    4,233

    Plant a tree or even better plant lots of trees...

    Plant a tree or even better plant lots of trees :cool: Wait 50 years, then harvest them.
  24. Replies
    98
    Views
    8,666

    What's wrong with 'qwerty' or 'yuiop'? No one...

    What's wrong with 'qwerty' or 'yuiop'? No one would ever think of using them.
  25. Replies
    258
    Views
    13,408

    All this blathering about manual vs. CNC makes me...

    All this blathering about manual vs. CNC makes me think the craftsmen of the 18th and 19th century were more skilled with files and saws :)...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4