Search:

Type: Posts; User: lakeside53

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. Freezing the shaft won't do much - the bearing...

    Freezing the shaft won't do much - the bearing inner will stay close to shaft temperature. Nothing says you cannot pull on the outer race. Obviously at some point you will damage the race or...
  2. Replies
    9
    Views
    366

    If you really want to plate restoration of the...

    If you really want to plate restoration of the surface is the hard part. You will need to strip the old plating and electro-clean to remove the rust, then polish (if enough base material) and/or...
  3. easy. Find someone with a generator (listen... ...

    easy. Find someone with a generator (listen... you can hear them) and pay them to charge your car.
  4. Replies
    9
    Views
    205

    Just keep looking until you find the right one,...

    Just keep looking until you find the right one, or....

    If you do use a 208/120 Y panel, and don't want any 120v circuits, forget the neutral (but still run ground) and then any three adjacent...
  5. Replies
    9
    Views
    205

    To be code compliant you need a panel that is...

    To be code compliant you need a panel that is listed for 240 DELTA. Sure, at home you can get away with anything... like using a 208/120 panel and not using the neutral bar etc. Take care...
  6. 18 months ago I went from 29 years of driving my...

    18 months ago I went from 29 years of driving my 1990 Mazda B2600 to a Toyota Tacoma TRD sport. Both 4wd, 5 and 6 speed manual respectively. I missed my old truck for a short while. Got to like...
  7. Replies
    23
    Views
    2,577

    You don't need to change the rectangular block -...

    You don't need to change the rectangular block - just re-positioning it by moving the index/securing hole in the big die so it kicks the rectangular block around (clockwise) another 20 degrees or...
  8. Replies
    23
    Views
    2,577

    If you want to do a 180 bend, move your die...

    If you want to do a 180 bend, move your die locking holes such that the rectangular block is angled "in" by 20 degrees (i.e. the max bend is 200 degrees). That will give allowance for spring-back. ...
  9. Replies
    9
    Views
    459

    3.0000 then Enter on mine... you don't have to...

    3.0000 then Enter on mine... you don't have to start at zero.
  10. So buy the angle stihl gearbox then. Both have...

    So buy the angle stihl gearbox then. Both have their uses. I have both.
  11. vape it!

    vape it!
  12. OSHA takes this seriously. We have 100 work...

    OSHA takes this seriously. We have 100 work station each with fume hoods connected to a central vac system or localized carbon scrubbers. For home use a small fan works fine.
  13. Replies
    17
    Views
    822

    I'm building tubing dies for my Diacro. This...

    I'm building tubing dies for my Diacro. This style for the main die https://www.suncoasttools.com/crm/ItemPage.aspx?ItemNumber=561.50025005690035TM&VendorNumber=TOOMEX

    and a corresponding ball...
  14. Replies
    18
    Views
    895

    OK, I got the context wrong ;) I done a few...

    OK, I got the context wrong ;)

    I done a few motor shafts, but the trick is to mount it in a 4 jaw, indicate that end then use a steady on the bearing surface of the "far" end for true, then re-cut...
  15. Replies
    18
    Views
    895

    Depends on the diameter, depth and required...

    Depends on the diameter, depth and required precision. And... cleaning-up often means little to no D.O.C., and that can be a problem for inserts so high positive rake is likely.

    I have boring...
  16. Thread: Hey Joe Lee

    by lakeside53
    Replies
    1
    Views
    204

    Hey Joe Lee

    Clean out your mail box so I can PM you ;)
  17. Replies
    28
    Views
    1,366

    I've worked in Brazil. English is not an issue...

    I've worked in Brazil. English is not an issue for industrial companies. Auto translations of technical requests can be awful; always test them by copying and translating back to English. If you...
  18. Replies
    10
    Views
    643

    You are fine. Like the other said - don't go...

    You are fine. Like the other said - don't go measuring to ground or neutral unless you understand what you are seeing. I suspect you made mistake the first time - the only legs you are going to...
  19. Replies
    46
    Views
    3,384

    You have 1/8th forstner bit? That's...

    You have 1/8th forstner bit? That's essentially what you make with a thin wall tube.
  20. Replies
    20
    Views
    1,936

    You are going to find that house paint latex is...

    You are going to find that house paint latex is awful in these unless thinned ridiculously. I rather brush it on that muck around trying to do a good job with one.
  21. Replies
    17
    Views
    975

    link? Pretty much everything draws power, but...

    link?

    Pretty much everything draws power, but does it have it's own battery? If so, almost nothing from your kubota's battery. Why not wire it to switched aux power - key on, voltmeter works and...
  22. Replies
    20
    Views
    1,936

    Having used all of the above and my Graco HP...

    Having used all of the above and my Graco HP pump, go rent one. I can spray 5 gallons direct from the bucket in a very short time, and with no thinning or mucking around. I do add Flotrol.
    ...
  23. Replies
    46
    Views
    3,384

    Just a quick trip to the grinder and touch outer...

    Just a quick trip to the grinder and touch outer edge so it has a 20 'ish degree taper on the edge. Don't over think it. It will cut perfect hole by coring out the material. Drill bits? - phooey....
  24. That is of course a dc motor with brushes!

    That is of course a dc motor with brushes!
  25. Replies
    46
    Views
    3,384

    Take a thin wall tube say 1/8 or whatever...

    Take a thin wall tube say 1/8 or whatever diameter, stainless is nice (don't use brass), but not essential, taper the end like a "punch", mount in a drill press and hey... paper core drill.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4