Search:

Type: Posts; User: JoeLee

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. WOW, talk about getting screwed from China no...

    WOW, talk about getting screwed from China no doubt. Nothing in that circuit to produce any ultrasonic sound waves. Would the average consumer ever know that?? Doubt it.

    I would send them back...
  2. Here is a pic of what I have to scribe the index...

    Here is a pic of what I have to scribe the index marks on. Pretty simple job, just have to figure out how to hold the part for the angle marks, unless I want to rotate the mills vise, would rather...
  3. I ground it in my T&C grinder so the the "rings"...

    I ground it in my T&C grinder so the the "rings" or rain of the grind are circular and not in line with the rod as they would be if I used a tungsten electrode grinder for TIG. I have one of those...
  4. The actual point of a dressing nib are not...

    The actual point of a dressing nib are not perfectly on center. The points are crude and would be hard to locate precisely.

    JL.............
  5. Interesting video. Is the spindle turning?? I...

    Interesting video. Is the spindle turning?? I couldn't tell.

    JL...............
  6. I had thought of running the spindle at high R's...

    I had thought of running the spindle at high R's but never thought of grinding a square point. Running the spindle with a round scribe point probably wouldn't do anything mor than dragging it would....
  7. I have a 1/4" dia. piece of tungsten that I...

    I have a 1/4" dia. piece of tungsten that I pointed in my T&C grinder years ago. This is what I've been using, but the sharp point keeps breaking, then I have to point it again. Too brittle when you...
  8. Never heard of this one. JL..............

    Never heard of this one.

    JL..............
  9. Best Material For Making Scribe Marks Using The Mill

    I need to scribe some index lines on a couple parts. I'm going to use my mill's XY for acuracy. I've done this before in the past but have difficulty keeping a point from breaking.
    I've tried solid...
  10. Replies
    26
    Views
    937

    My bro-inlaw made a set of forks for his skid...

    My bro-inlaw made a set of forks for his skid steer. I don't remember what they were made out of but since the max you can lift is only 600 lbs. I wouldn't be too concerned about the choice of steel....
  11. Replies
    20
    Views
    1,113

    I don't have a manual for this tool. If one...

    I don't have a manual for this tool. If one revolution of the screw increases or decreases the dia. by .625 then each index mark would be approximately .078 in dia.

    The marks are OK for a rough...
  12. Replies
    20
    Views
    1,113

    Thanks JR, that's what I needed. Yours is marked...

    Thanks JR, that's what I needed. Yours is marked much better than mine was. Nice heavy stamped or scribe marks. Mine were like etched or stenciled, wasn't much left to see, very faint.
    One other...
  13. Replies
    20
    Views
    1,113

    Hey JR...... What does the end of yours look like...

    Hey JR...... What does the end of yours look like where the button head adjusting screw is?? Does the screw head have a small slit in it and are there any index / reference marks on the end plate?? ...
  14. Replies
    20
    Views
    1,113

    Yep, I would never attempt to cut anything over...

    Yep, I would never attempt to cut anything over 4" with the R8, and I would probably lock the quill in case it want's to grab and pull down. I would raise the knee into it and get a feel for what is...
  15. Replies
    20
    Views
    1,113

    It's hard to keep up with all the buy outs and...

    It's hard to keep up with all the buy outs and mergers. You don't know who owns what anymore.
    I looked at that Michigan Drill site, under Availability: Special Order it says nothing available at any...
  16. Replies
    20
    Views
    1,113

    These guys have nothing for this. They told me...

    These guys have nothing for this. They told me they never sold any of these and never stocked any parts or cutters.

    JL..............
  17. Replies
    20
    Views
    1,113

    Literature.......... I also got a few original...

    Literature..........

    I also got a few original price sheets and sales brochures.

    These were pretty pricey back then. This one is dated 1996.
    ...
  18. Replies
    20
    Views
    1,113

    Here is a picture of what I got. It's really...

    Here is a picture of what I got. It's really clean except for the two end caps which are pretty well pitted. I was going to see if I could price new ones or just make them. They did have some crude...
  19. Replies
    20
    Views
    1,113

    No, I found one last year for $200. It's the 12"...

    No, I found one last year for $200. It's the 12" model. Would rather have the 6" one but I couldn't pass it up for the price. I don't think it's been used much, only two of the assorted cutters look...
  20. Replies
    20
    Views
    1,113

    Holex Corp. Trepanning Tool

    Is this company still around making these?
    Or were they bought out, sold, went out of business, merged etc??

    JL.....
  21. Thread: Collet Question

    by JoeLee
    Replies
    9
    Views
    486

    You might find something in a metric size collet...

    You might find something in a metric size collet that fits better. It's good to have both.

    Or, you can make a split collet out of any piece of scrap round you have in the shop. Drill it to fit...
  22. I have an older Yantai 8" that is horizontal and...

    I have an older Yantai 8" that is horizontal and vertical. I can't find anything to complain about other than the oval bolt slots for the vertical position don't match the the spacing of my BP table...
  23. Replies
    32
    Views
    1,848

    So they don't snap under their own weight. ...

    So they don't snap under their own weight.

    JL..............
  24. Replies
    31
    Views
    2,178

    I wouldn't waste my time, even if it were given...

    I wouldn't waste my time, even if it were given to me. It looks like they have already broken through the top.

    JL..............
  25. Replies
    31
    Views
    2,178

    Must be an ebay listing....... everybody selling...

    Must be an ebay listing....... everybody selling scrap machine tooling there thinks they have gold!

    JL.............
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4