Search:

Type: Posts; User: doctor demo

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    109
    Views
    7,394

    I believe the most recent speed record in a...

    I believe the most recent speed record in a streamliner that is wheel (propulsion) driven is 503 mph and was by team Vesco.
    Yes very sad indeed, but accidents happen, I would rather be killed doing...
  2. Replies
    16
    Views
    1,814

    I thought U of A football . I don't think it is a...

    I thought U of A football . I don't think it is a law that you have to live in Arizona to be a fan, but I am not absolutely sure of that :rolleyes:

    Steve
  3. Replies
    13
    Views
    1,009

    Well, in re-reading the OP and looking at your...

    Well, in re-reading the OP and looking at your link, I believe you are correct and that I was visualizing something completely different. I originally thought he was describing what was going on at...
  4. Replies
    26
    Views
    4,270

    Hi Chris the simplest way,if I understand you...

    Hi Chris the simplest way,if I understand you ,would to make or buy some transfer screws like thees...
  5. Replies
    13
    Views
    1,009

    I think that he is looking for something like...

    I think that he is looking for something like this: https://www.fillernecksupply.com/fuelflex_male_to_female_gas_diesel_fuel_line_e85_connectors_splice_reducer_adapters/
  6. Replies
    31
    Views
    3,819

    It's not a total loss, those two Allen screws...

    It's not a total loss, those two Allen screws look pristine!

    Steve
  7. Replies
    4,498
    Views
    1,392,727

    Your big Allis looks a lot like a dozer I ran off...

    Your big Allis looks a lot like a dozer I ran off and on for a few years. Do you have a ''tool carrier'' set up or just a dozer blade on a loader?

    Steve
  8. Replies
    56
    Views
    11,181

    It sounds like someone did a motor swap, what rpm...

    It sounds like someone did a motor swap, what rpm is on the motor plate?

    Steve
  9. Replies
    124
    Views
    8,607

    I didn't have anything better to do the other...

    I didn't have anything better to do the other night so I read the link you provided. I found some of it very interesting and other parts, well, not so much. But I did learn a lot.

    As far as your...
  10. Replies
    94
    Views
    7,991

    George, You aren't confusing ounces and pounds...

    George, You aren't confusing ounces and pounds again are you?;)

    Steve
  11. Replies
    54
    Views
    5,174

    What is a matchbook cover? Is that some sort of...

    What is a matchbook cover? Is that some sort of facebook app? Lol!
    How about asking a kid to use a mimeograph machine?
    Or ask for a dime to make a phone call?
    Pilgrim!


    Steve:cool:
  12. Crumple zones Disc brakes Air bags Steve

    Crumple zones
    Disc brakes
    Air bags

    Steve
  13. Replies
    4,498
    Views
    1,392,727

    I bought a Cincinnati #5 universal horizontal 80"...

    I bought a Cincinnati #5 universal horizontal 80" mill several years ago, and the seller loaded it on the truck with their large overhead gantry crane using the eye bolt in the ram:eek:. I still have...
  14. Replies
    22
    Views
    4,141

    And Torker and Kingweld? Haven't noticed...

    And Torker and Kingweld?
    Haven't noticed anything from Forrest Addy either.

    Steve
  15. Will your plasma torch cut 4 to 6 inch thick...

    Will your plasma torch cut 4 to 6 inch thick material like the op mentioned?
    If it will, it must be pricey!

    Steve
  16. Don't beat yourself up too badly over it, with a...

    Don't beat yourself up too badly over it, with a little bit of re--designing you can salvage that part.
    End mills can pull out of collets also. It has happened to me, and probably more people than...
  17. Replies
    51
    Views
    4,345

    I don;t have any "skin in the game" on this...

    I don;t have any "skin in the game" on this particular topic, however if my friend has switched from Sunnen oil to Chevron oil 40 or so years ago and is pleased with all that goes with it, and is...
  18. Replies
    51
    Views
    4,345

    The Chevron Bright cut metalworking fluid is...

    The Chevron Bright cut metalworking fluid is around six bucks a gallon less expensive in small 5 gal. pails ,bulk also gets discounted. Prices probably vary depending on location also....
  19. Replies
    51
    Views
    4,345

    A good friend of mine has a automotive machine...

    A good friend of mine has a automotive machine shop with at least two maybe three different Sunnen hones, He quit buying their oil back in the seventies because of the high price that Sunnen wants....
  20. Joe Pesci and Marisa Tomei, and it also relates...

    Joe Pesci and Marisa Tomei, and it also relates to the op's original question. "Dead on, balls accurate" torque wrench calibration.:p

    Steve:cool:
  21. Same to you Brian ! I'm only 8 months older and...

    Same to you Brian !
    I'm only 8 months older and smarter though, my birthday is in April:p
    Keep up all of the great builds, it seems that everyone enjoys them as much as you do making them.

    Steve
  22. It's a good thing that I don't live close, I...

    It's a good thing that I don't live close, I clicked on a few pages and had to stop torturing myself. I found lots of stuff I would be bidding on. :D

    Steve
  23. Replies
    31
    Views
    3,339

    Hey Paul, That's a cool little IH. Is it a...

    Hey Paul,
    That's a cool little IH.
    Is it a "TD" model comparable in size to a D-2 Cat, or s it a gas rig? Late 1960's or early 1970's era I'm guessing .

    Steve
  24. Replies
    18
    Views
    1,758

    Madman, check your private msg. box. Steve

    Madman, check your private msg. box.

    Steve
  25. Replies
    24
    Views
    1,842

    Just a friendly reminder, NEVER use an oxygen...

    Just a friendly reminder, NEVER use an oxygen gauge for anything but oxygen. If you do and the gauge is returned to oxygen service the results can be deadly, weather you are a cheap or rich...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4