My week this week! My workshop videos.

[hermetic]

Hi All
This week I get the last coat of paint on the LoVolite and leave it to bake off in the workshop we get all the bits of the new kennel transported up the field, assembled and finished, and even get the roof on! So whats left to do? Everything!, no seriously we need to put felt and gutter on the large kennel block and then the whole project is finished and we can get back onto the field clearance which is what we started on! We have another unexpected fly in the ointment though, Keiths car clutch, which john and I replaced only a couple of months ago, has failed! John reckons the (brand new) clutch cover spring has failed! I will keep you informed of the outcome! the areas we cut with the Fordson are ready for another cut, so that will be next weeks first job, unless we are car hunting, or in the workshop if wet! Thanks for watching and don't forget to like, comment and subscribe!
Phil, East Yorkshires been HOT this week and so humid!

[hermetic]

Hi All

This week I am back in the workshop due to the weather! it has rained on and off all week! The Lovolite rebuild continues, we get a new car for keith due to the Volvos demise, and I repair two faults on the Ryobi chainsaw We did a little field work in final preparation for a much smaller than usual Wicani Jamboree, but were so rushed in between the rain I didn't get much time for filming!

Phil, in increasingly soggy East Yorkshire.

[hermetic]

Hi All
A very mixed bag this week, a couple of days of workshop fixes and Fordson major and topper working on the field topping out the regrowth on the bramble patch we cleared earlier this year. The tractor started (just) after a couple of months, and all running fine after my last attempt to blow it up when the water ran low because the rad was leaking and I didn't check the level before I started!! All running sweet, good oil pressure, cool running and no dramas, so I set up a couple of cameras, went back to the tractor, and it wouldn't start! in fact it was totally dead. I jumped it off from the Toro2CV tractor (which ran out of petrol mid charge) and then proceeded to finish the area and took the tractor to a power point and put the charger on it......nothing, ammeter didn't budge, and a test proved the battery to be open circuit! Probably a broken internal link. £166 later we have a new 900 amp one, and boy does she start, although at that price I would expect it to cut the field by itself! I will be back to it Monday, weather permitting, this will probably be the last cut of the season. Phil, in lovely late summer East Yorkshire.

[hermetic]

Hi All Which indeed? Keith and I went to look at, and bought, a mobility scooter for Angela to ride round the field on so she can get through her very demanding day a bit easier! We ttried it, I rode it, and he bought it, but when we got it home, we realised that it was fine on the flat, but even the slightest incline bogged it down! I have come to the conclusion that it has had the wrong control PCB bodged in some long time ago, not by the guy we bought it off, who sold it in good faith, as I found the screws holding the cover over the PCB were rusted solid. Looking at it from this end, it was a bad buy, we are trying to find a wiring diagram,and the spec of the board that SHOULD be in it! Got the spares for the chainsaw, and fitted them, and it starts, then stops! more attention required! Got the new handle on the pressure wash finished, so I suppose something has gone right this week, and Martyn came over Friday, fitted a couple of security cams for me, and set up the network so that I can view them remotely And I had a ride in a Teswla, and the wildlife cam too, and then he took me for a ride in his wifes Tesla, which ,although he is a complete computer nerd, he hates! Me, being a bit of a prat, forgot to video it, but the acceleration was much MORE than impressive!!

Phil, Summer has been switched off in East Yorkshire!

[hermetic]

Hi All A very hot week in which both field work and shop work get done! Lots of grass cutting with the Fordson, and i got video to prove it! and also some workshop time working on a couple of old stairlifts that are being sold off as a project. a little generator, and I fix the yardcam as well. lots of stuff to interest the eclectic tastes of my viewers (I Hope!!) Hard to get into anything apart from an iced G&T when it's so hot!
Phil, in sweltering East Yorkshire!

[hermetic]

Hi all, A short one this week as we got involved in a very dirty and boring clean up operation which I didn't bother filming to save you the drudgery of sitting through it! I got the stairlifts repaired and working, and fixed the spark problem on the brigs and stratton on the little generator, but thats about all Next week we have more grass to cut, a tree to fell, and looking at the weather, more workshop time!
Phil, in Autumnal but still warm East Yorkshire.

[hermetic]

Hi All, This video was made with Clipchamp, but it won't be made with it ever again! what an execrable piece of crap it is! Microshaft have disabled video editor, and replaced it with clipchamp which is grossly overcomplex, and doesn't work. It would normally take me about 1-1/2 hours tops to turn raw footage into a video, I started at 7 and now its after 10 and I havent finished yet! Clicked the tab to arrange clips in ascending order, didn't work! neither did descending order! Tried to click in the text box to add screen text, it didn't work, but when you rewatch the video it has inserted "type text here" into the video, and by clicking on the screen I was eventually able to add the text I wanted! Trust Microshaft to take a simple and usefull piece of software that works perfectly and completely screw it up! RANT OVER!! Lots of repairs of kit I have for sale, and a recalcitrant Ryobi chainsaw which I think I got to the bottom of! Unfortunately Keiths wife, Angela is in Hospital at the moment, which means the looking after, cleaning out and feeding of 30 odd dogs has fallen on our shoulders, so I only get an hour or two in the workshop a few days a week! Normal service will be resumed as soon as possible, please bear with me!
Phil, in Calm, peacefull and sunny East Yorkshire