General

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Topics	Statistics	Last Post
Closed, Sticky: Advertiser List by George Bulliss Started by George Bulliss, 07-02-2021, 11:52 AM	0 responses 429 views 7 likes	Last Post by George Bulliss 07-02-2021, 11:52 AM
Sticky: Favorite Threads by George Bulliss Started by George Bulliss, 04-21-2010, 02:26 PM	1 response 123,221 views 1 like	Last Post by PStechPaul 06-24-2021, 01:24 AM
tool gloat- probably not by darryl Started by darryl, 05-28-2020, 10:57 PM	7 responses 378 views 0 likes	Last Post by 754 05-29-2020, 05:36 PM
Source for 5" dia Brass tube/pipe ? by darylbane Started by darylbane, 05-26-2020, 02:43 PM	27 responses 746 views 0 likes	Last Post by daryl bane 05-29-2020, 12:45 AM
Forming an Eccentric Head on a Capscrew by wierdscience Started by wierdscience, 05-27-2020, 08:55 PM	20 responses 616 views 1 like	Last Post by JoeLee 05-28-2020, 11:48 AM
Tool post grinder by darryl Started by darryl, 05-24-2020, 04:58 PM	20 responses 716 views 0 likes	Last Post by darryl 05-28-2020, 02:28 AM
Way OT:::::: Brain surgery for Parkinson's disease by becksmachine Started by becksmachine, 05-27-2020, 05:16 AM	10 responses 416 views 0 likes	Last Post by brian Rupnow 05-27-2020, 07:18 PM
Chunky Little Motor from Scrap Pile only 4 wires by Tundra Twin Track Started by Tundra Twin Track, 05-21-2020, 10:28 PM	31 responses 950 views 0 likes	Last Post by Tundra Twin Track 05-27-2020, 11:33 AM
OT: Pakistan Airlines 8303 crash by wierdscience Started by wierdscience, 05-24-2020, 11:51 PM	25 responses 1,116 views 0 likes	Last Post by wierdscience 05-27-2020, 08:48 AM
Non circular boring... (fun with Linuxcnc of course..) by skunkworks Started by skunkworks, 03-08-2020, 08:22 PM	64 responses 2,329 views 3 likes	Last Post by skunkworks 05-27-2020, 12:01 AM
My adventures in casting by Dan Dubeau Started by Dan Dubeau, 05-11-2020, 11:20 PM	42 responses 1,307 views 1 like	Last Post by Dan Dubeau 05-26-2020, 08:04 PM
Birthday on tuesday will be 69 so birthday tips WITH ENGINEERING CONTENT by Alistair Hosie Started by Alistair Hosie, 05-16-2020, 07:13 AM	16 responses 433 views 0 likes	Last Post by Illinoyance 05-26-2020, 05:30 PM
Good old Harbor Fright strikes again. by J Tiers Started by J Tiers, 05-21-2020, 05:22 PM	68 responses 2,013 views 0 likes	Last Post by J Tiers 05-26-2020, 04:56 PM
Ring roller advice. by plunger Started by plunger, 05-10-2020, 04:41 AM	24 responses 695 views 0 likes	Last Post by 754 05-26-2020, 03:52 PM
Too many welders. Thin the herd? by AWS Started by AWS, 05-22-2020, 07:49 PM	14 responses 453 views 0 likes	Last Post by mattthemuppet 05-26-2020, 12:57 PM
Carbide insert tool holder clamps available? by challenger Started by challenger, 05-25-2020, 11:47 AM	14 responses 282 views 0 likes	Last Post by The Metal Butcher 05-26-2020, 12:16 PM
Job loss recovery and your shop by RB211 Started by RB211, 05-24-2020, 03:17 PM	32 responses 1,038 views 0 likes	Last Post by darryl 05-26-2020, 02:13 AM
Repowering Startrite Vertical Bandsaw by Tundra Twin Track Started by Tundra Twin Track, 04-10-2020, 10:30 PM	6 responses 293 views 0 likes	Last Post by Captain K 05-25-2020, 09:56 PM
TE-CO/Parlec mill vises? by wierdscience Started by wierdscience, 05-24-2020, 12:27 PM	14 responses 412 views 0 likes	Last Post by wierdscience 05-25-2020, 04:10 PM
Bearing Interference Fit by Spindle Started by Spindle, 05-25-2020, 08:48 AM	12 responses 278 views 0 likes	Last Post by Tim The Grim 05-25-2020, 12:14 PM
oil pump for drilling by dian Started by dian, 05-23-2020, 02:53 AM	3 responses 203 views 0 likes	Last Post by BCRider 05-25-2020, 12:04 PM
OT: Nice neighborhoods by J Tiers Started by J Tiers, 05-23-2020, 12:02 PM	30 responses 927 views 1 like	Last Post by thaiguzzi 05-25-2020, 10:37 AM

Previous 1 111 161 201 206 207 208 209 210 211 212 213 214 215 216 221 261 311 711 1211 3822 template Next

No topics found.

Mark This Channel Read

Announcement