Announcement

Collapse
No announcement yet.

Other Smithy Owners ?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • smiller6912
    replied
    All's well...

    I received my DRO this morning and I have it installed. I had only two minor problems, first- one of the mounting plates was taped for M6 (per the instruction) and there were M5s in the hardware pack, second- one of the "Y" axis mounting screws went thru the mounting angle and up against the cross slide table, I had to shorten it by 8mm. Other than that installation was a breeze (well except for the hour and a half that it took to index everything in plumb and square).
    The display mounting arm is up to you to locate. The pictures that Smithy sent me showed them using a vertical column on the right rear of the chip tray, I brought home a 3x3x1/4 angle from the shop to use in that location but decided I liked it better on my left so I used a 3" piece of 4x2x1/4 that I had here and mounted it to the top of the gear box cover. I like it there as I don't have to reach over the machine to get to it and it is right over the rest of the controls. I have been told that some people mount it to the wall behind the machine, that wasn't going to work for me.
    I found out that the first units that they received had the mounting hardware fabricated backwards. It seams that the Chinese use first angle projection and we use third angle projection on the detail drawings (I've run into that problem before with European drawings). So, some of the first people to get them had quite a hard time figuring out the mounting. I believe that has been fixed with the ease that I installed mine.
    It is loaded with way more bells and whistles that I normally use but I'm going to try them out.
    According to sino-ld website, these have an accuracy of .0002, we shall see.

    All in all, I'm very happy, so far.....................

    Leave a comment:


  • JerryL
    replied
    New Sino DRO for Granite

    Hi All
    I got my Smithy 1324 Granite in July 2007. I was to receive a FREE DRO as part of my package ... The machine came and the DRO was on back order . I waited and called and waited until about Sept .
    Smithy kept saying they had changed over to a new Brand / Style and where getting the installation parts made etc .

    I got it and it was the Sino... I started to try and hook it up and the directions at that time where about useless and very skimpy and NOT CLEAR AT ALL.

    It ended up that I had to make several spacers / bushings / and Modify 2 of the brackets .....

    I was on the phone several times with Smithy and they where very helpful and gave some suggestions ..... They also sent me a replacement Mounting rail for the Y Axis .

    I had gotten one of the VERY FIRST ones that they sent out the day after they got them from their supplier .......

    Smithy did take care of me for all the probs . THEY ARE VERY GOOD AT DOING THAT FOR A CUSTOMER ..

    The SINO has way more features than I'll ever use or want .... It is VERY SENSITIVE and reads down to 0.000000 You breathe on it and it changes .
    That I know of there is no way to make the read out less sensitive or use less digits .

    I would rather have a DRO that just gives you a +/- Position and read to 0.0000 ( Tens of Thousandths )

    If was free so I guess I can't complain .

    JerryL
    Last edited by JerryL; 02-14-2008, 11:48 AM.

    Leave a comment:


  • torchroadster
    replied
    I'll be anxious to read your report on the install and performance of your SINO DRO. Did he tell you what the accuracy specs were? I asked them a while back and they didn't have the numbers yet.

    Leave a comment:


  • smiller6912
    replied
    Dro.......

    I called Smithy today about the new DRO and talked to Kerry Ballard, he could not have been more helpful. First he told me that the first units that they got (Sino) were sent with the mounting hardware made backwards (for you drafters, its a first angle / third angle thing), second he sent me pictures and diagrams and descriptions of how he installed the one in their store.
    I mentioned to him that I thought that I was feeling a wobble in the lathe spindle, he immediately explained that the tapered roller bearings were set loose at the factory for breaking in and how to adjust them, it worked great.
    After a bit of joking around with him, he ended up giving me a $100 discount on the Sino DRO and the shipping.
    Great people, they always have the right answer.
    (Make sure you have time to talk, he does like to chat).

    Leave a comment:


  • torchroadster
    replied
    I usually lurk on the general site, but saw this and wanted to check in. I have a Smithy Granite 1340 - bought it used a little over a year ago.

    Leave a comment:


  • JerryL
    replied
    Smithy ...great In Help

    Hi Sam

    SMITHY has been VERY GOOD to me and very helpful as well as EVERYONE is VERY knowledgeable about their products and machining .

    I have called then at least a dozen times with various prob that I have encountered and they have helped me through EVERY TIME and then some .

    I wasn't " Bitching " about them . I was just thinking that if they offered what I had described ,maybe it would save someone who is a first time buyer and don't care to tinker with the machine or at least as little as possible a option.

    I don't know how the other 3 in 1 machines are or compare as well as their tech support teem etc .
    But judging from what i read about the top selling 3 - 5 brands of 3 in 1 and single use mills / lathes Smithy has the least complaints in the last 4 - to present years .
    If I had it to do all over again I think I would go the same way I did , but going now with Smithys top of the line Granite Max machine .

    Take care have fun be safe ...... JerryL

    Leave a comment:


  • smiller6912
    replied
    Originally posted by JerryL
    I am wondering if SMITHY would do a COMPLETE SET UP / CHECK OUT ( For REAL ) on a machine if a buyer asked them to ...of course for a nominal charge .
    JerryL
    I have had real good luck with their tech. department, they are always very helpful and seam to know the machines "inside and out". I was having a little chuck runout problem and a call to them narrowed it down to a cam lock stud, the FREE replacement was in my mailbox the next day.
    What could it hurt to give them a call..........

    Leave a comment:


  • JerryL
    replied
    Smithy & Set Up / Check Out

    I already have a SMITHY 1324 Granite (2007) Version.

    I am wondering if SMITHY would do a COMPLETE SET UP / CHECK OUT ( For REAL ) on a machine if a buyer asked them to ...of course for a nominal charge .

    1. I mean take the gibs out polish / hone them .

    2. Check all the gears for alignment and any burs etc .

    3. Check the chuck for run out / tail stock in line with head spindle/

    4. Check out the mill head and column.

    5. Make sure that the speed dial and motor are in sync .

    6. whatever else that could be set up before shipping .

    Just a thought ???

    JerryL

    Leave a comment:


  • smiller6912
    replied
    Fyi

    I ordered the quick change tool post for my G1324. It came today, it is worth every penny ($229). I've had it half a day and already saved an hour setup time. NO MORE SHIMS, YIPEEEEE.......
    http://www.smithy.com/accessories.ph...&aid=812&code=
    check it out...............

    Leave a comment:


  • JerryL
    replied
    Smithy Granite 1324 / July 2007

    Hi to the group

    I bought my Smithy Granite 1324 ( regular one ) in July / 2007 . the shipping was great as well as the packing .

    I unloaded the machine from a very low utility trailer with a 2 1/2 ton cherry picker / engine puller and it had the load leveler bar with it . I used a combination of chains and nylon straps .
    I also used this equipment to lift it into place onto the Smith stand / bench .

    I have had some leg / back issues and have not been able to do a lot as far as checking it out and setting it up let alone doing much machining .

    I did have some chuck run out and fixed / adjusted that . I had a tapper problem and I THINK I have that solved .... I cleaned / honed and adjusted ALL the Gibbs on anything that has them ... I had a real problem mounting the new style DRO as I was one of the first to get the new units that they started using . ( had to make several of my own shims / bushings and get different screws )
    So far I like the machine ...but I think there are a few other tweaks and adjustments that will have to be made ???

    If I was to do it all over again I'd have gotten the INDUSTRIAL SMITHY and or I see they have a new model Granite with all kinds of zippy bells and whistles ..... Mainly for the motor and the bearings )

    I will try to make posts as I go along here now that I am somewhat feeling better and able to stand while by the machine .

    JerryL JerryLeskovec
    Last edited by JerryL; 01-28-2008, 01:48 AM.

    Leave a comment:


  • smiller6912
    replied
    Smithy SALE............

    Just in case anyone has been thinking of buying a new Smithy, I just got a flier in the mail and through Feb. 29 they are including a free $375 machine stand. (I love mine). The offer does not show up on the web site, you have to call 800-476-4849.

    Leave a comment:


  • monkeyb0y
    replied
    AGI DVDs

    I've seen the lathe series and they are really pretty well done. They cover the basics very well. They are pricey to buy but they are available at Smartflix.com (formerly Technical Video Rental) a video rental site like Netflix but for instructional videos. They have a good selection of machinist video and very reasonable prices.

    Leave a comment:


  • rustyswarf
    replied
    Own a Smithy

    I've had a Smithy 1220 since 1995. It has been good to me. I made about $700 with it making parts for a 3-ton ice machine for an AC/Refridgeration mech. friend of mine. Made a replacement hood latch for a friend's Caddy coupdeville (freebie job) that his car dealer wanted $500 for. Made pins for obsolete firearms and replacement pins for reloading dies that were hard to find for my friends. Made brass panhead screws for 1890's era Victrola phonographs--(have a friend that collects and restores them). Made new bushings and spindle shaft for a friend's 1936 Atlas lathe that went down. That job showed me how accurate a Smithy can be. I make tools and parts for my friend's wood lathes.
    Best thing I ever did was convert it to a Phase II quick change tool post set up. The Phase II (piston type) was good, but the base plate and shaft that came with it was a nightmare. It leaned. Underneath the bottom of the top half of the compound slide is a slot milled out to hold the Smithy 4-way toolpost shaft from rotating. I got a harder grade bolt and nut from the hardware store. Cut a new busing that fit inside the QC toolpost body that fit the hole and the new bolt closely (to tighten tolerances). Ground the head of the bolt to fit the milled slot in the underside of the compound slide, and put everything together. Only other thing I had to do since I usually work with 1/2" toolbits, was mill a little off the bottoms of the QC toolholders so I could get on center. Voila! Quick and dirty QC toolpost fitting.

    Leave a comment:


  • Vintage Mutes
    replied
    Lol - umm $500 for a few DVDs is outta my price range. If I had that moola available I'd put it toward a dedicated mill. But thanks anyway.

    Leave a comment:


  • smiller6912
    replied
    $$$$$$$$$$$$

    It ain't cheep but it's on DVDs.............
    http://www.americangunsmith.com/allitems.php?page=8
    I have a friend who really likes this, I have only seen a short portion but, I found it useful. Call them, I think that they have some deal for the full machine shop set.

    "This is not an endorsement, I have not used this program"
    "Use at your own risk", "mileage may very"

    Leave a comment:

Working...
X