.png)
No content found
Please log in to your account to view your subscribed posts.
| Directory | Topics | Posts | Last Post |
|---|---|---|---|
|
General
This forum reserved for general machining discussion. Off topic threads are allowed, but will be closed if they go too far off track or become too numerous. Please add “OT” to the title of any off topic thread. Discussions on religion, politics, or “For Sale” posts are not allowed.
Topics: 74,499
Posts: 1,275,848
Last Post:
OT tough pick up trucks.
|
74,499 | 1,275,848 |
|
|
Topics: 1,138
Posts: 13,033
|
1,138 | 13,033 |
by vpt
Yesterday, 07:54 AM
|
|
Digital Machinist
A place for CNC projects and discussion. "For Sale” posts are not allowed.
Topics: 585
Posts: 6,279
|
585 | 6,279 |
|
|
Gunsmithing
Discuss gunsmith projects and techniques here. Political, gun control, or "For Sale" posts will not be allowed.
Topics: 1,144
Posts: 11,806
Last Post:
1890’s artillery sights
|
1,144 | 11,806 |
|
|
Networking
Need to brainstorm? Feeling isolated? Here's another forum for you to connect with other hobby machinists who share your specific interest. Fill in the information slots and add a brief statement about your interest and whom you would like to hear from. You can remove your listing at any time. "For Sale” posts are not allowed.
Topics: 561
Posts: 4,193
Last Post:
Bevel gear cutter
|
561 | 4,193 |
|
|
Third Hand
This forum is for seeking and finding help in a variety of ways. You may be seeking advice on a way of solving a problem you have in your shop. Or possibly you just bought a used lathe or some other machine tool, but the seller didn't have an owner's manual, parts list or operating instructions, so you are in need of one. Perhaps you want to contact a manufacturer, but don't have any information about their address or phone. In other words, any help you need can be solicited here. One thing we insist upon, however; this is not a place to sell something. Also, out of courtesy to the helper, the offer of payment for photocopies and postage is certainly in order.
Topics: 4,115
Posts: 29,654
|
4,115 | 29,654 |
|
There are currently 278 users online. 48 members and 230 guests.
Most users ever online was 16,648 at 07:47 PM on 09-29-2019.
-
I recently picked up a Talyvel 1 electronic level. No real need for it other than lust. It was in excellent condition, but apparently had been placed...Today, 11:07 AM
-
Nasty tire wear:
This should not be happening.
No, it is not alignment. Had that checked....Yesterday, 06:14 PM -
Pressing a 3/4" shank over the original three sided arbor help reduce the noise and chatter by quite a bit. It even helped tighten up the tolerances...Yesterday, 11:26 AM
-
Nasty tire wear:
This should not be happening.
No, it is not alignment. Had that checked....Yesterday, 06:14 PM -
I have no intentions on doing so (yet), but can a guy run a VFD off a 220v single phase generator? Like I said, I have no intentions of doing it but it...06-22-2021, 09:58 AM
-
Pressing a 3/4" shank over the original three sided arbor help reduce the noise and chatter by quite a bit. It even helped tighten up the tolerances...Yesterday, 11:26 AM
-
I have a maple tree that has several trunks that extend from a single base trunk. The way the tree is situated, one of the trunks lean toward our house....06-21-2021, 07:50 PM
-
I have just finished bringing a power hacksaw back to life. There is no relieving device for the pressure on the blade, The crankshaft revolves in an...06-22-2021, 07:53 AM