.png)
I am sure those LED's in warm weather work fine, but let me tell you about the LED's I have on my patio, here in Green Bay Wisconsin
I have a string...
Rich Carlstedt
Senior Member
Last Activity: Today, 10:55 AM
Joined: 07-27-2001
Location: Green Bay, WI
-
Rich Carlstedt replied to New to me 1929 wide (heavy?) 9" long bed and overhead silent drive casting tradein GeneralMatt, You brought a smile to my face 😀😀😀
You don't normally hear about Tools not assembled. My first home shop Lathe and...Leave a comment:
-
Rich Carlstedt replied to DRO head location 14x40 lathe - where do you prefer / where to you despise location?in GeneralWe had both at work, mounted over the headstock and swing arm off the carriage .
The problem with swing arm is it was a two hand operation. when...Leave a comment:
-
Don't need a indicator or hex block or any instruments
Get a hex nut the same size and chuck either a tap drill or threaded stock in the drill chuck....Leave a comment:
-
One of the problems with using a carbide endmill on Hard Material ( 60+ Rc) is maintaining constant pressure of the tool on the work-piece.
A Carbide...Leave a comment:
-
Joe, check the volume of oil. Pump the pump several times and note the flow.. Is it the same for all 4 top saddle surfaces ?
There are metering...Leave a comment:
-
Joe
You have the second generation table drive.
before you disassemble the taper pin, mark the shaft and collar with paint or nail polish...Leave a comment:
-
Super Rare M head..has 7 steps for speed
BP had 3 collets sizes. MT 2, ( 88 % )--B& S #7 ( 10 %) and then a third which was a BP taper was...Leave a comment:
-
This Simpson 260 was given to me on my 16th birthday 65 years ago
Still does Yeoman service.
He was a Mechanic by day and ran a Radio-TV repair...Last edited by Rich Carlstedt; 10-10-2020, 05:39 PM.Leave a comment:
-
Hold on a moment .
There are two thread forms
1/8-27 NPS and 1/8-27 NPT
NPS is straight thread
NPT is tapered thread ( for sealing...Leave a comment:
-
Linear brake ?
Make a Tapered hole (less than 7 Degrees) and then make a collet with a matching taper.
The collet should be for your shaft...Leave a comment:
-
Joe, my 1943 Bridgeport ( no powerfeed ) also had the Zerk fittings for oil and like you, I pulled the table and drilled and tapped into all the lube...Leave a comment:
-
So much for " Maximum Space Utilization"
We had a forklift driver go through a 8" Cinderblock wall and it was comical as...Leave a comment:
-
What I should have said above is that most after market table drives will slide off with just a key.
If it's a factory install table drive, then...Leave a comment:
-
Joe, Normally the right hand side is easier to pull on a BP since it is the floating side
There are so many table drives (BP had 3 ) with aftermarket...Leave a comment:
-
Joe, here is the drawing.
It does not have power feed, but that is on the right anyway
Rich
...Leave a comment:
-
You do not need to remove the Lead screw .
Just remove the left side handle , Dial and Lead screw bearing ring , then the endcap ( It's pinned)...Leave a comment:
-
The digital adapters are OK, but For speed, you want a spring clamp like this
https://www.ebay.com/i/330631637823?...norover=1&mkev...Leave a comment:
-
Always Start the thread at the bottom , then you reduce accidents, don't contend with chips, and can climb mill all the way out , and don't worry about...Leave a comment:
-
If you use an Eyebolt, IT MUST BE A FORGED EYEBOLT
Welded eyebolts are too iffy
RichLeave a comment:
No activity results to display
Leave a comment: